~roperty Property Class Head Markings Class Nul Markings QgaO 5 @~@O 46 .
NoMark No Mark !l @ ~ @ 98 O~ 10 © ~ @) Q~ 12.9 Q~ 12 @ ~ @ CTM-7 (5-89) 2R3; 001 15 110589 IN.m(lb.in) N.m(lb-in) N.m(lb-ft) N.m(lb·ft) N.m(lb·ft) N.m(lb·ft) 5.0(3.5) 7.0(5) 6.5(4.5) 9.0(6.5) 7.5(5.5) 10.0(7.5) 8.5(6) 12.0(9) 11.0(8) 15.0(11) 13.0(9.5) 18.0(13) 70(52) 100(74) 95(70) 130(97) 110(81) 150(111) 115(85) 155(114) 150(111) 205(151) 175(129) 240(177) 180(133) 245(180) 235(173) 315(232) 275(203) 370(273) 320(236) 435(321) 375(277) 510(376) 455(356) 620(457) 535(395) 725(535) 620(457) 840(620) 725(535) 985(726) 790(583) 1070(789) 925(682) 1255(926) 1155(852) 1565(1154) 1350(996) 1835(1353) 1570(1158) 2130(1571) 1835(1353) 249O(1837) 2135(1575) 2900(2139) 2500(1844) 3390(2500) 2740(2021) 3720(2744) 3205(2364) 4355(3212) AB6;T5234, T5235 053;TORQ4.
090888 OIL DRY OIL DRY OIL DRY 21.0(15) 30(22) 25(18) 35(26) 30(22) 45(33) 40(30) 55(41) 55(41) 75(55) 65(48) 85(63) 9.8 10.9 12.9 48 QgaO No Mark 88 Q~ 109 General DIA.
WRENCH OIL DRY OIL DRY OIL SIZE DRY N.m(lb-'t) N.m(lb-ft) N-m(lb-ft) N.m(lb·ft ) N·m(lb,'t) N.m(lb·ft) M5 8mm 1.5(1) 2.5(1.5) 2.5(1.5) 3.0(2) 4.5(3.5) 6.0(4.5) M6 10mm 3.0(2) 4.0(3) 4.0(3) 5.5(4) 7.5(5.5) 10.0(7.5) M8 13mm 7.0(5) 9.5(7) 10.0(7.5) 13.0(10) 18.0(13) 25(18) Ml0 16mm 14.0(10) 19.0(14) 20.0(15) 25(18) 35(26) 50(37) M12 18mm 25(18) 35(26) 35(26) 45(33) 65(48) 85(63) M14 21mm 40(30) 50(37) 55(41) 75(55) 100(74) 140(103) M16 24mm 60(44) 80(59) 85(63) 115(85) 160(118) 215(159) M18 27mm 80(59) 110(81) 115(85) 160(118) 225(166) 305(225) M20 30mm 115(85) 160(118) 165(122) 225(166) 320(236) 435(321) M22 33mm 160(118) 215(159) 225(167) 305(225) 435(321) 590(4~5) M24 36mm 200(148) 275(203) 285(210) 390(288) 555(409) 750(553) M27 41mm 295(218) 400(295) 415(306) 565(417) 810(597) 1100(811) M30 46mm 400(295) 545(402) 565(417) 770(568) 1100(811) 1495(1103) M33 51mm 545(402) 740(546) 770(568) 1050(774) 1500(1106) 2035(1500) M36 55mm 700(516) 950(700) 990(730) 1345(992) 1925(1420) 2610(1925) Litho in U.S.A.
01·15 CAUTION: Use only metric tools on metric hardware. Other tools may not fit properly. They may slip and cause injury. DO NOT use these values if a different torque value or tightening procedure is listed for a specific applica- tion. Torque values listed are for general use only. Shear bolts are designed to fail under predetermined loads. Always replace shear bolts with identical grade. Fasteners should be replaced with the same or higher grade. If higher grade fasteners are used, these should only be tightened to the strength of the original. Make sure fastener threads are clean and you properly start thread engagement. This will prevent them from failing when tightening.
Tighten cap screws with plastic insert or crimped steel-type lock nuts to approximately 50 percent of amount shown in chart. Tighten toothed or serrated- type lock nuts to full torque value. 4.6 4.8 8.8 METRIC SERIES TORQUE CHART Check tightness of cap screws periodically. AllTractorManuals.com