daewoo — Daewoo SB4136E00 Service Manual for G420E/G424E Tier LP Engine Lift Trucks

IATSensorInputHigh: (Intake Air Temperature Sensor Input is High) normally set if the TMAP temperature signal wire has become disconnected or the circuit is open to the SECM. EST1Low: (Electronic Spark Trigger) is a current driver signal and normally set if the signal from the SECM is shorted to ground. EST1High: (Electronic Spark Trigger) is a current driver signal and normally set if the signal from the SECM is open or lost. LowOilPressure: (Low Oil Pressure) the oil pressure switch has opened or become disconnected, normally indicating a low oil condition in the engine. BatterySensorInputLow: (Battery Voltage Sensor Input is Low) normally set if the power to the SECM drops below 8.5 VDC.

BatterySensorInputHigh: (Battery Voltage Sensor Input is High) normally set if the power to the SECM increases above 15.9 VDC. XDRPSensorInputLow: (Transducer Voltage Sensor Input is Low) normally set if the sensor power from the SECM drops below 4.8 VDC. XDRPSensorInputHigh: (Transducer Voltage Sensor Input is High) normally set if the sensor power from the SECM increases above 5.9 VDC. EngineOverspeed: (Engine Over speed) is set when the engine RPM increases above the SECM maximum governing RPM. Typically this is in association with one or more throttle faults. This fault can be set without additional throttle faults if the operator motors the lift truck down a steep grade (hill).

Pedal1SensorInputLo: (Accelerator Pedal Position 1 Sensor Input is Low) normally set if the APP1 signal wire has become disconnected or the circuit is open to the SECM. Pedal1SensorInputHi: (Accelerator Pedal Position 1 Sensor Input is High) normally set if the APP1 signal wire has become shorted to APP power, APP1 has failed or the SECM has failed. Pedal1SensorRangeLo: (Accelerator Pedal Position 1 Sensor Range is Low) the APP1 potentiometer has malfunctioned. An improper APP1 reading may be due to dirt or oxidation on the sensor traces. Pedal1SensorRangeHi: (Accelerator Pedal Position 1 Sensor Range is High) the APP1 potentiometer has malfunctioned.

An improper APP1 reading may be due to dirt or oxidation on the sensor traces. Pedal2SensorInputLo: (Accelerator Pedal Position 2 Sensor Input is Low) normally set if the APP2 signal wire has become shorted to APP power, APP2 has failed or the SECM has failed. Pedal2SensorInputHi: (Accelerator Pedal Position 2 Sensor Input is High) normally set if the APP2 signal wire has become disconnected or the circuit is open to the SECM. Pedal2SensorRangeLo: (Accelerator Pedal Position 2 Sensor Range is Low) the APP2 potentiometer has malfunctioned. An improper APP2 reading may be due to dirt or oxidation on the sensor traces. Pedal2SensorRangeHigh:

(Accelerator Pedal Position 2 Sensor Range is Low) the APP2 potentiometer has malfunctioned. An improper APP2 reading may be due to dirt or oxidation on the sensor traces. Pedal1ToPedal2Difference: (Accelerator Pedal Position Sensor 1 and Accelerator Pedal Position Sensor 2 are Different) normally set when APP1 measured pedal position is different from APP2 measured pedal position. AFRTrimValveOutput: (Air Fuel Ratio Trim Valve (FTV) Driver) is normally set when the FTV driver signal is open due to the connector becoming disconnected. AFRTrimValveLowerDC:

(Air Fuel Ratio Trim Valve (FTV) Lower Duty Cycle) normally set when the duty cycle of the FTV reaches the minimum limit (running too lean). AFRTrimValveUpperDC: (Air Fuel Ratio Trim Valve (FTV) Upper Duty Cycle) normally set when the duty cycle of the FTV reaches the maximum limit (running too rich). O2SensorSwitching: (Oxygen Sensor Switching) is set when the O2 sensor can no longer switch or be driven above and below 500mv by the SECM. OxygenSensorInputHigh: (Oxygen Sensor Input is High) OxygenSensorInputLow: (Oxygen Sensor Input is Low) G420E/G424E Tier LP Engine Advanced Diagnostics 47