86 6 SPN 5~ ...........continued TYPE SPN FMI En- gine Ma- chine type Description ECM 5234 82 12 Y E Shutoff path fault 5 ECM 5234 82 12 Y L Shutoff path fault 5 ECM 5234 83 12 Y E Shutoff path fault 6 ECM 5234 83 12 Y L Shutoff path fault 6 ECM 5234 84 12 Y E Shutoff path fault 7 ECM 5234 84 12 Y L Shutoff path fault 7 ECM 5234 85 12 Y E Shutoff path fault 8 ECM 5234 85 12 Y L Shutoff path fault 8 ECM 5234 86 12 Y E Shutoff path fault 9 ECM 5234 86 12 Y L Shutoff path fault 9 ECM 5234 87 12 Y E Shutoff path fault 10 ECM 5234 87 12 Y L Shutoff path fault 10 ECM 5234 88 0 Y E Recognition error of engine speed ECM 5234 88 0 Y L Recognition error of engine speed ECM 5234 89 0 Y E Rail pressure fault (The actual rail pressure is too high during PRV limp home) ECM 5234 89 0 Y L Rail pressure fault (The actual rail pressure is too high during PRV limp home) ECM 5234 91 0 Y E Rail pressure fault (Injector B/F tem- perature error during PLV4 limp home) ECM 5234 91 0 Y L Rail pressure fault (Injector B/F tem- perature error during PLV4 limp home) ECM 5242 86 31 C F Aftertreatment 1 Diesel Oxidation Catalyst System- Special Instruction ECM 5242 86 31 C E Aftertreatment 1 Diesel Oxidation Catalyst System- Special Instruction ECM 5242 86 31 C L Aftertreatment 1 Diesel Oxidation Catalyst System- Special Instruction ECM 5245 31 C F Aftertreatment SCR Operator In- ducement Active - Condition Exists ECM 5245 31 C E Aftertreatment SCR Operator In- ducement Active - Condition Exists ECM 5245 31 C L Aftertreatment SCR Operator In- ducement Active - Condition Exists ECM 5246 0 C E Aftertreatment SCR Operator In- ducement - Data valid but above nor- mal operational range - Most Severe level ECM 5246 0 C L Aftertreatment SCR Operator In- ducement - Data valid but above nor- mal operational range - Most Severe level ECM 5246 0 P E Aftertreatment SCR Operator In- ducement Severity :
High - most se- vere (3) ECM 5246 0 P L Aftertreatment SCR Operator In- ducement Severity : High - most se- vere (3) ECM 5246 0 C F Aftertreatment SCR Operator In- ducement - Data valid but above nor- mal operational range - Most Severe level continued.......... ...........continued TYPE SPN FMI En- gine Ma- chine type Description ECM 5246 15 P E Aftertreatment SCR Operator In- ducement Severity: High - least se- vere(1) ECM 5246 15 P L Aftertreatment SCR Operator In- ducement Severity: High - least se- vere(1) ECM 5246 16 P E Aftertreatment SCR Operator In- ducement Severity: High - moderate severity (2) ECM 5246 16 P L Aftertreatment SCR Operator In- ducement Severity:
High - moderate severity (2) MCU 525 4 * E Ram Lock Solenoid-Voltage Below Normal, Or Shorted To Low Source MCU 525 4 * L Ram Lock Solenoid-Voltage Below Normal, Or Shorted To Low Source MCU 525 6 * E Ram Lock Solenoid-Current Above Normal Or Grounded Circuit MCU 525 6 * L Ram Lock Solenoid-Current Above Normal Or Grounded Circuit MCU 5260 9 * L DCT1 TIMEOUT Timeout of CAN- message DCT1 from display comput- er MCU 527 4 * E Creep Solenoid-Voltage Below Nor- mal, Or Shorted To Low Source MCU 527 4 * L Creep Solenoid-Voltage Below Nor- mal, Or Shorted To Low Source MCU 527 6 * E Creep Solenoid-Current Above Nor- mal Or Grounded Circuit MCU 527 6 * L Creep Solenoid-Current Above Nor- mal Or Grounded Circuit MCU 5270 9 * L JSS TIMEOUT Timeout of CAN- message JSS from Joystick Steering Controller MCU 5271 9 * L DISPID1 TIMEOUT Timeout of _ CAN-message DISPID1 from display controller MCU 5280 9 * L ENGINE CONF TIMEOUT Timeout of CAN-message ENGINE CONF from engine controller ECM 5285 1 S E Boost temperature to high, not plau- sible ECM 5285 1 S L Boost temperature to high, not plau- sible ECM 5285 1 S F Boost temperature to high, not plau- sible MCU 5290 9 * L EEC1 TIMEOUT Timeout of CAN- message EEC1 from EEC controller ECM 5298 17 C F Aftertreatment Diesel Oxidation Cat- alyst Conversion Efficiency - Data Valid But Below Normal Operating Range - Least Severe Level ECM 5298 18 C F Aftertreatment 1 Diesel Oxidation Catalyst Conversion Efficiency - Data Valid But Below Normal Operating Range - Moderately Severe Level ECM 5298 17 C E Aftertreatment 1 Diesel Oxidation Catalyst Conversion Efficiency - Data Valid But Below Normal Operating Range - Moderately Severe Level ECM 5298 17 C L Aftertreatment 1 Diesel Oxidation Catalyst Conversion Efficiency - Data Valid But Below Normal Operating Range - Moderately Severe Level ECM 5298 17 P E Aftertreatment 1 Diesel Oxidation Catalyst Conversion Efficiency :
Low - least severe (1) ECM 5298 17 P L Aftertreatment 1 Diesel Oxidation Catalyst Conversion Efficiency : Low - least severe (1) ECM 5298 18 C E Aftertreatment 1 Diesel Oxidation Catalyst Conversion Efficiency - Data continued..........