89 6 SPN 5~ ...........continued TYPE SPN FMI En- gine Ma- chine type Description ECM 5419 31 S L Throttle M42, service mode enabled ECM 5419 9 S E Throttle M42 has detected a CAN timeout ECM 5419 9 S L Throttle M42 has detected a CAN timeout ECM 5419 5 P E Engine Throttle Actuator #1 : Current Below Normal ECM 5419 5 P L Engine Throttle Actuator #1 : Current Below Normal ECM 5419 5 S E Throttle M42, current limited ECM 5419 5 S L Throttle M42, current limited ECM 5419 6 P E Engine Throttle Actuator #1 : Current Above Normal ECM 5419 6 P L Engine Throttle Actuator #1 :
Current Above Normal ECM 5419 6 S E Throttle M42, overload ECM 5419 6 S L Throttle M42, overload MCU 5420 2 * L STARTING GEAR SIGNAL CAN sig- nal for starting gear is defective ECM 5421 3 S E Wastegate actuator, short circuit to +24V ECM 5421 3 S L Wastegate actuator, short circuit to +24V ECM 5421 4 S E Wastegate actuator, short circuit ECM 5421 4 S L Wastegate actuator, short circuit ECM 5421 5 C E Engine Turbocharger 1 Wastegate Actuator 1 - Current Below Normal or Open Circuit ECM 5421 5 C L Engine Turbocharger 1 Wastegate Actuator 1 - Current Below Normal or Open Circuit ECM 5421 5 S E Wastegate actuator, short circuit to ground ECM 5421 5 S L Wastegate actuator, short circuit to ground ECM 5421 6 S E Wastegate actuator, short circuit ECM 5421 6 S L Wastegate actuator, short circuit ECM 5421 3 S F Wastegate actuator, short circuit to +24V ECM 5421 4 S F Wastegate actuator, short circuit ECM 5421 5 S F Wastegate actuator, short circuit to ground ECM 5421 6 S F Wastegate actuator, short circuit MCU 5430 2 * L ENGINGE TORQUE SIGNAL CAN signal for engine torque is defective MCU 5431 9 * L ENGINE SPEED LIMIT FUNCTION DOES NOT WORK PROPERLY DURING STALL OR OUTPUT- SPEED LIMIT FUNCTION MCU 5440 2 * L REFERENCE ENGINE TORQUE SIGNAL CAN signal for reference of engine torque is defective MCU 5450 2 * L ACTUAL ENGINE TORQUE SIG- NAL CAN signal for actual engine torque is defective MCU 5470 2 * L EEC2 TIMEOUT Timeout of CAN- message EEC2 from EEC controller MCU 5480 3 * L S.C.
TO BATTERY VOLTAGE AT CLUTCH K1 the measured resist- ance value of the valve is out of limit, the voltage at K1 valve is too high. MCU 5480 4 * L S.C. TO GROUND AT CLUTCH K1 the measured resistance value of the valve is out of limit, the voltage at K1 valve is too low. continued.......... ...........continued TYPE SPN FMI En- gine Ma- chine type Description MCU 5480 5 * L O.C. AT CLUTCH K1 the measured resistance value of the valve is out of limit.
ECM 5484 3 C F Engine Fan Clutch 2 Control Circuit - Voltage above normal, or shorted to high source ECM 5484 4 C F Engine Fan Clutch 2 Control Circuit - Voltage below normal, or shorted to low source ECM 5484 3 C E Engine Fan Clutch 2 Control Circuit - Voltage above normal, or shorted to high source ECM 5484 3 C L Engine Fan Clutch 2 Control Circuit - Voltage above normal, or shorted to high source ECM 5484 4 C E Engine Fan Clutch 2 Control Circuit - Voltage below normal, or shorted to low source ECM 5484 4 C L Engine Fan Clutch 2 Control Circuit - Voltage below normal, or shorted to low source MCU 5490 3 * L S.C.
TO BATTERY VOLTAGE AT CLUTCH K2 the measured resist- ance value of the valve is out of limit, the voltage at K2 valve is too high. MCU 5490 4 * L S.C. TO GROUND AT CLUTCH K2 the measured resistance value of the valve is out of limit, the voltage at K2 valve is too low. MCU 5490 5 * L O.C. AT CLUTCH K2 the measured resistance value of the valve is out of limit.
ECM 5491 3 C F Aftertreatment Diesel Exhaust Fluid Line Heater Relay - Voltage above normal, or shorted to high source ECM 5491 4 C F Aftertreatment Diesel Exhaust Fluid Line Heater Relay - Voltage below normal, or shorted to low source ECM 5491 7 C F Aftertreatment 1 Diesel Exhaust Flu- id Line Heater Relay - Mechanical system not responding or out of ad- justment ECM 5491 3 C E Aftertreatment Diesel Exhaust Fluid Line Heater Relay - Voltage above normal, or shorted to high source ECM 5491 3 C L Aftertreatment Diesel Exhaust Fluid Line Heater Relay - Voltage above normal, or shorted to high source ECM 5491 31 C E Aftertreatment 1 Diesel Exhaust Flu- id Line Heater Relay - Condition Ex- ists ECM 5491 31 C L Aftertreatment 1 Diesel Exhaust Flu- id Line Heater Relay - Condition Ex- ists ECM 5491 4 C E Aftertreatment Diesel Exhaust Fluid Line Heater Relay - Voltage below normal, or shorted to low source ECM 5491 4 C L Aftertreatment Diesel Exhaust Fluid Line Heater Relay - Voltage below normal, or shorted to low source ECM 5491 7 C E Aftertreatment 1 Diesel Exhaust Flu- id Line Heater Relay - Mechanical system not responding or out of ad- justment ECM 5491 7 C L Aftertreatment 1 Diesel Exhaust Flu- id Line Heater Relay - Mechanical system not responding or out of ad- justment TCU 55 * * L JSS TIMEOUT TCU 55 * * F FRONT WHEEL DRIVE STATUS TIMEOUT MCU 5500 3 * L S.C.
TO BATTERY VOLTAGE AT CLUTCH K3 the measured resist- ance value of the valve is out of limit, the voltage at K3 valve is too high. continued..........