9803/3280 Issue 1 Note: All the clutches work on the same principle. For a full description of operation see Systems Description . On 6 speed gearboxes, the 6 speed clutch X is controlled via solenoid valve Xs . Note: The 6 speed clutch assembly is so called as it is fitted to 6 speed, and not 4 speed gearboxes. However, the clutch is NOT engaged when 6th gear is selected. See the adjacent table. Both the mainshaft and the layshaft assemblies have a single clutch each. Solenoid valve Zs , when energised, directs pressurised oil to the layshaft clutch Z . Solenoid valve Ys , when energised, directs pressurised oil to the mainshaft clutch Y .
The reverse clutch assembly C is similar to the forward clutch assembly. It contains two hydraulically operated clutches; one clutch ( W ) provides a reverse low ratio drive and the other ( V ) a reverse high ratio drive. 2-position solenoid valves when energised, direct pressurised oil to either the reverse low (solenoid Ws ), or reverse high (solenoid Vs ) clutch. Forward clutch assembly B contains two hydraulically operated clutches; one clutch ( T ) provides a forward low ratio drive and the other ( U ) a forward high ratio drive. Each clutch is controlled by a 2-position solenoid valve.
When the applicable solenoid is energised, pressurised oil is directed to either the forward low (solenoid Ts ) or forward high (solenoid Us ) clutch. The torque converter A is a fluid coupling bolted to a drive plate which in turn is bolted to the engine flywheel. As the engine starts to rotate, the converter gives smooth power take off gradually increasing the torque transmitted. This torque is transferred from the converter assembly to the clutch/gear assemblies via input shaft on the forward clutch assembly B . Oil from the torque converter A flows out of the gearbox at position M to the external oil cooler 6 , returning to the solenoid valve manifold block 5 at position N .
The oil then flows through internal oilways providing lubrication for clutches and bearings before returning to the gearbox sump. the filter back through the casing to the torque converter A . Pressure in the converter is controlled by a relief valve G which dumps oil from the converter line back to the sump. Oil pump converter. 17 - 4 17 - 4 Section F Section F Note: Solenoid valve Xs controls clutch X , solenoid valve Zs controls clutch Z and so on. The tables show which clutches and solenoids are engaged for each gear selection. In the schematic, the gearbox is shown with 2nd gear forward engaged. 2nd gear forward requires the forward low clutch T and layshaft clutch Z to be engaged.
When the gear selection switch is moved to 2nd gear forward, the electrical control system energises solenoid valves Ts and Zs . Pressurised oil is diverted to the back of pistons in both clutches to engage the drive. At the same time all other solenoids are de-energised, diverting oil from the back of the other clutch pistons to the gearbox sump. 4WD clutch S is also energised to give 4 wheel drive. Example - 2nd gear forward 4WD (6 speed gearbox) When a gear is selected via the control switch in the cab, 2 clutches are always engaged. By selecting different pairs of clutches different gear ratios are engaged. On 4 speed gearboxes the solenoids are electrically controlled using relays.
On 6 speed gearboxes the solenoids are controlled by an electronic control unit (ECU) mounted in the cab. Speed sensor 1 is used to enable the gear selection to be managed automatically as required.
Purchased from www.WorkshopManuals.co.uk Ss Ys 6th U,Y - 5th T,Y - 4th X,Y V,Y 3rd U,Z W,Y 2nd T,Z V,Z 1st X,Z W,Z Gear Clutches engaged 6 Speed Powershift 4th U,Y V,Y 3rd T,Y W,Y Zs Xs Ts Ws Vs Forward Reverse Us 5 1 Speed sensor 5 Solenoid valve manifold block 6 Gearbox oil cooler A Torque converter B Forward clutch assembly C Reverse clutch assembly D Mainshaft assembly E Layshaft assembly F 2/4 wheel drive clutch assembly G Torque converter relief valve H Oil pressure maintenance valve J Transmission oil pump K 6 speed assembly (if fitted) L 4WD output yoke M Hose connection - to oil cooler N Hose connection - from oil cooler P Oil strainer Q Oil filter R Driveshaft (drives machine main hydraulic pump) S 2/4WD clutch Ss 2/4WD clutch solenoid T Forward low ratio clutch Ts Forward low ratio clutch solenoid U Forward high ratio clutch Us Forward high ratio clutch solenoid V Reverse high ratio clutch Vs Reverse high ratio clutch solenoid W Reverse low ratio clutch Ws Reverse low ratio clutch solenoid X 6 speed clutch (6 speed gearbox only) Xs 6 speed clutch solenoid (6 speed gearbox only) Y Mainshaft clutch Ys Mainshaft clutch solenoid Z Layshaft clutch Zs Layshaft clutch solenoid Key 4 Speed Powershift Gear Clutches engaged Forward Reverse 1st T,Z W,Z 2nd U,Z V,Z 3rd T,Y W,Y 4th U,Y V,Y 6 Speed Powershift Gear Clutches engaged Forward Reverse 1st X,Z W,Z 2nd T,Z V,Z 3rd U,Z W,Y 4th X,Y V,Y 5th T,Y - 6th U,Y - Ts Us Ws Vs Ss Ys 5 Zs Xs shopManuals.co.uk ed Powershift Clutches engaged Forward Reverse T,Z W,Z U,Z V,Z T,Y W,Y U,Y V,Y ed Powershift Clutches engaged Forward Reverse X,Z W,Z T,Z V,Z U,Z W,Y X,Y V,Y T,Y - U,Y -