9808/3280 Issue 1 LA LB LC LE FA FB1 FG Note: FL GB GC GG Note: h1 h2 h3 h4 h5 For gearbox solenoid actuation see subsequent pages. Input Controls Before fault finding make sure that you understand how the the electrical circuits work. The most effective method of fault finding is by means of ShiftMaster Daignostics software and a laptop PC, see Service Procedures, Powershift Gearbox - 6 speed, ShiftMaster Diagnostis - User Guide. Having identified a faulty system, use the schematics to identify the relevant wires and connectors, continuity checks can then be carried out using a multimeter. Gearbox solenoid coils can be checked for the correct resistance value as given in Technical Data .
See Service Procedures, Electrical Testing Methods for more details. The wire numbers and colours, where appropriate, are shown as an aid to identification whilst fault finding. On the electrical diagram opposite the electrical connectors (example, FA to LA) are shown looking on the mating face of each connector when they are disconnected. Electrical Connections - Wires and Connectors Schematics are divided into 2 parts: Input Controls and Gearbox Solenoid Actuation .
Powershift Gearbox - 6 Speed 33 - 7 33 - 7 Section F Section F Electrical Connections Transmission Splices h2 SB SC Splices (h1) SA SC SF SJ SL SS Connectors (h4) NH h4 О h3 NG Transmission dump switch MB1 Earth point Connectors (h3) CA h3 О h4 CB h3 О h2 CM Park brake warning light relay CCA Fuses DR2 Earth point DZ Park brake relay DW Park brake switch EA Immobiliser EAB Link - immobiliser (if immobiliser is not fitted) www.WorkshopManuals.co.uk Purchased from www.WorkshopManuals.co.uk C10 LC LA C17 LE GG FG MB1 NG LB CB NH CA DR2 DW A408640 Powershift Gearbox - 6 Speed Electrical Connections - Wires and Connectors Schematics are divided into 2 parts:
Input Controls and Gearbox Solenoid Actuation. On the electrical diagram opposite the electrical connectors (example, FA to LA) are shown looking on the mating face of each connector when they are disconnected. The wire numbers and colours, where appropriate, are shown as an aid to identification whilst fault finding. Before fault finding make sure that you understand how the the electrical circuits work. The most effective method of fault finding is by means of ShiftMaster Daignostics software and a laptop PC, see Service Procedures, Powershift Gearbox - 6 speed, ShiftMaster Diagnostis - User Guide.
Having identified a faulty system, use the schematics to identify the relevant wires and connectors, continuity checks can then be carried out using a multimeter. Gearbox solenoid coils can be checked for the correct resistance value as given in Technical Data. See Service Procedures, Electrical Testing Methods for more details. Input Controls For gearbox solenoid actuation see subsequent pages. Component Key (Input controls): The following key identifies the component connectors on the opposite diagrams. Note that the wires coloured red show the electrical ‘live feed’ to the column gear lever and gearbox E.C.U..
h1 Harness - 721/10937 Front console h2 Harness - 721/10971 Link h3 Harness - 721/10970 Side console h4 Harness - 721/10935 Engine/mainframe h5 Harness - 721/10941 Transmission Note: For harness drawings see Section C. Connectors (h1) FA h1 Î h2 FB1 Earth point FG Transmission dump relay Note: Identify dump relay FG by locating wire 1873 at pin 2 of the corresponding relay base. FL Column gear lever GB E.C.U. connector A GC E.C.U. connector B GG Throttle switch Connectors (h2) LA h2 Î h1 LB h2 Î h3 LC h2 Î h5 LE Kick down switch