www.WorkshopManuals.co.uk Removal and Replacement (cont’d) IMPORTANT: The gearbox is heavy. Unless it is safely supported during removal and replacement it could fall and cause injury. Make sure that you have access to suitable jacks and a gearbox locating ‘cradle’ before attempting to remove the gearbox. 11 At a later stage the gearbox and engine assembly is tilted to allow access to fixing bolts. To prevent damage as the engine is tilted components must have their fixings removed as follows: ! WARNING A raised and badly supported machine can fall on you. Position the machine on a firm, level surface. Before raising one end ensure the other end is securely chocked.
Do not rely solely on the machine hydraulics or jacks to support the machine when working under it. a Fuel sediment bowl assembly E (2 bolts). b Exhaust stack fixing bracket F (2 bolts). d Radiator fan cowl G (4 bolts). It is not necessary to remove these components, only release them from their fixings. Disconnect the battery, to prevent the engine being started while you are beneath the machine. GEN 1-1 12 Support the gearbox using a suitable trolley jack and cradle. The gearbox must be securely located on the cradle as shown at Y . 13 Make sure that the weight of the gearbox is supported by the trolley jack and then remove the gearbox mounting bolts H .
Removal 1 Park the machine on firm level ground. The gearbox is heavy. If the ground is soft or uneven it will not be possible to remove the gearbox safely. 14 Using the trolley jack, lower the gearbox and engine to gain access to the top torque converter housing to engine block retaining bolts J . Put a support under the engine as shown at Z to prevent it from dropping when the gearbox is removed. 2 Loosen the right side rear wheel nuts. Rest the shovel on the ground and lower the stabilisers to raise the rear of the machine. Check dimension X which must be at least 800 mm. This will allow the gearbox to be pulled clear. Block/support the machine.
15 Undo the four bolts J at the top of the torque converter housing. Note that the two outer most bolts have nuts instead of screwing into the engine block. Also note the position of the electrical earth straps. Note: On sideshift machines, suitable lengths of steel channel can be used as safety struts between the stabiliser feet and chassis, one at each stabiliser. 16 Pull off the breather tube K . Undo the gearbox dipstick fixing nut L and then remove the dipstick tube. 3 Remove the right hand side rear wheel. 17 Uncouple the forward/reverse solenoid valve connectors M , oil pressure sender N and temperature sender P (if fitted). Label the connectors for identification when refitting.
4 Remove the bonnet - see Section 3, Routine Maintenance . 5 Disconnect the gearshift from the top of the gearbox, as shown at A . 18 Disconnect the gearbox oil cooler hoses R . 19 On 4 wheel drive machines, uncouple the electrical connector at the 4WD solenoid S . 6 Remove the rear axle propshaft - see Propshafts . 7 Disconnect the front axle driveshaft bolts B (use tool 892/00822). 20 Remove the flywheel housing to engine bolts T. 21 Manoeuvre the gearbox with the torque convertor clear of the engine housing. 8 Drain the hydraulic tank and remove the main hydraulic pump (see Section E, Service Procedures and Main Hydraulic Pump ). Tie the suction hose up clear of the gearbox.
22 Lower the trolley jack and pull the gearbox and torque convertor clear of the machine. 9 Drain the gearbox oil, see Section 3, Routine Maintenance . 10 Remove the access bung/plate at the bottom of the torque converter housing. Through the access hole, loosen and remove the torque converter to engine flywheel retaining bolts D . 9803/3280 Purchased from www.WorkshopManuals.co.uk Issue 1 Section F Transmission Section F 105 - 2 105 - 2 Synchro Shuttle Gearbox