. MAINTENANCE TIGHTENING TORQUE SPECIFICATIONS TIGHTENING TORQUE SPECIFICATIONS TIGHTENING TORQUE LIST CAUTION Apply the following table for Hydraulic Hose. 4 - 13 If nuts, b olts, or oth er parts are not tightened to th e specified torque, i t wil l cause looseness or dam age to the tightened part s, and this will cause failu re of the m achine o r problems with operation. Always p ay careful attention w hen tightening par Unless otherwise specified , tighten the metr ic nuts and bolts to t he torque shown in th e table below. If it is ne cessary t o replace any nut or bolt, always use a Komatsu genuine part of the sa me size as the part tha t was replaced.
Thread diameter of bolt (a)(mm) Width across flats (b)(mm Tightninig torque [Nm (kgm)] Target value Permissible range ) Permissible range 6 8 10 12 14 10 13 17 19 22 13.2 (1.35) 31 (3.2) 66 (6.7) 113 (11.5) 177 (18.0) 11.8 - 14.7 (1.2 - 1.5) 27 - 34 (2.8 - 3.5) 59 - 74 (6.0 - 7.5) 98 - 123 (10.0 - 12.5) 157 - 196 (16.0 - 20.0) 16 18 20 22 24 24 27 30 32 36 279 (28.5) 382 (39.0) 549 (56.0) 745 (76.0) 927 (94.5) 245 - 309 (25.0 - 31.5) 343 - 425 (35.0 - 43.5) 490 - 608 (50.0 - 62.0) 662 - 829 (67.5 - 84.5) 824 - 1030 (84.0 - 105.0) 27 30 33 36 39 41 46 50 55 60 1320 (135.0) 1720 (175.0) 2210 (225.0) 2750 (280.0) 3280 (335.0) 1180 - 1470 (120.0 - 150.0) 1520 - 1910 (155.0 - 195.0) 1960 - 2450 (200.0 - 250.0) 2450 - 3040 (250.0 - 310.0) 2890 - 3630 (295.0 - 370.0) 42 65 3830 (390.0) 3430 - 4220 (350.0 - 430.0) Thread diameter a (mm) Width across flats b (mm) Tightening torque Target value Permissible range Nm kgm lbft Nm kgm lbft 10 14 14.7 1.5 10.8 12.7 - 16.7 1.3 - 1.7 9.4 - 12.3 14 19 29.4 3.0 21.7 27.5 - 39.2 2.8 - 4.0 20.3 - 28.9 18 24 78.5 8.0 57.9 58.8 - 98.1 6.0 - 10.0 43.4 - 72.3 22 27 1 17.7 12.0 86.6 88.3 - 137.3 9.0 - 14.0 65.1 - 101.3 24 32 1 47.1 15.0 108.5 117.7 - 176.5 12.0 - 18.0 86.8 - 130.2 30 36 2 15.7 22.0 159.1 176.5 - 245.2 18.0 - 25.0 130.2 - 180.8 33 41 2 55.0 26.0 188.1 215.7 - 284.4 22.0 - 29.0 159.1 - 209.8