Maintenance - Section 4 OM4042 Page 40-4 Lubrication and Service 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 10 HOUR (DAILY) INSPECTION Truck Serial Number Site Unit Number Date ______________________ _______________ _______________ Hourmeter Name of Service Technician _____________ ___________________________________ TASK COMMENTS CHECKED INITIA MACHINE - Inspect the entire machine for leaks, worn parts, and damage. Repair as necessary. FAN DRIVE AND TURBOCHARGERS - Check for leaks, vibration or unusual noise. Check alternator and fan belt condition and alignment. RADIATOR - Check coolant level and fill with proper mixture as shown in Cooling System Recommenda- tion Chart.
Refer to Engine Manual for proper DCA levels. ENGINE - Check oil level. Refer to engine manufac- turer's manuals for oil recommendations. Lube Key A. FUEL FILTER - Drain water from bottom of filter hous- ing. FUEL STRAINER - Drain water and sediment at drain cock. MOTORIZED WHEELS - Refer to G.E. Motorized Wheel Service & Maintenance Manual for lubrication specifications and service intervals. AIR CLEANERS (NOT SHOWN) - Check air cleaner vacuum gauges in operator cab. The air cleaner(s) should be serviced, if the gauge(s) shows the follow- ing maximum restriction: Komatsu Engine: 25 in. of H2O vacuum*. NOTE:
After service, push the reset button on face of gauge to allow the gauge to return to zero. AIR CLEANERS See Section C of the service manual for servicing air cleaner elements. Empty air cleaner dust caps. After service, push the reset button on face of gauge (if equipped) to allow the needle to return to zero. . WHEELS AND TIRES - a. Inspect tires for proper inflation and wear. b. Inspect for debris embedded in cuts or tread. After each wheel mounting operation, recheck wheel mounting capscrew tightness after approximately five hours of operation, again at the end of the shift and then periodically until all capscrews hold at the pre- scribed 450 ft.lbs. (610 N.m) torque.
This requirement is prescribed for both front and rear wheels. . BODY UP SWITCH (NOT SHOWN) - Clean sensing area of any dirt accumulation. Truck Serial Number Site Unit Number Date ______________________ _______________ _______________ Hourmeter Name of Service Technician _____________ ___________________________________ TASK COMMENTS CHECKED INITIA LS MACHINE - Inspect the entire machine for leaks, worn parts, and damage. Repair as necessary. FAN DRIVE AND TURBOCHARGERS - Check for leaks, vibration or unusual noise. Check alternator and fan belt condition and alignment. RADIATOR - Check coolant level and fill with proper mixture as shown in Cooling System Recommenda- tion Chart.
Refer to Engine Manual for proper DCA levels. ENGINE - Check oil level. Refer to engine manufac- turer's manuals for oil recommendations. Lube Key A. FUEL FILTER - Drain water from bottom of filter hous- ing. FUEL STRAINER - Drain water and sediment at drain cock. MOTORIZED WHEELS - Refer to G.E. Motorized Wheel Service & Maintenance Manual for lubrication specifications and service intervals. AIR CLEANERS (NOT SHOWN) - Check air cleaner vacuum gauges in operator cab. The air cleaner(s) should be serviced, if the gauge(s) shows the follow- ing maximum restriction: Komatsu Engine: 25 in. of H2O vacuum*. NOTE:
After service, push the reset button on face of gauge to allow the gauge to return to zero. AIR CLEANERS See Section C of the service manual for servicing air cleaner elements. Empty air cleaner dust caps. After service, push the reset button on face of gauge (if equipped) to allow the needle to return to zero. WHEELS AND TIRES - a. Inspect tires for proper inflation and wear. b. Inspect for debris embedded in cuts or tread. After each wheel mounting operation, recheck wheel mounting capscrew tightness after approximately five hours of operation, again at the end of the shift and then periodically until all capscrews hold at the pre- scribed 450 ft.lbs. (610 N.m) torque.
This requirement is prescribed for both front and rear wheels. BODY UP SWITCH (NOT SHOWN) - Clean sensing area of any dirt accumulation.