OM4205 Maintenance - Section 4 Automatic Lube System Page 42- 13 Assembly 8. Assemble crank rod assembly, to pump with bush- ings (13) and button head screws (12). Tighten screws to 100 - 110 in. lbs. (11.3 - 12.4 N.m) torque. Note: Use Loctite ® 242 (or equivalent) thread locker on all torqued, threaded connections. Use extreme care to prevent thread locker from flowing into adjacent areas such as clearance fits and ball check. Allow a minimum of 30 minutes cure time before operating pump. 9. Place pump subassembly (parts 1 through 28) into pump housing (46). 10. Install new O-ring (54), backup washer (53) and O- ring (52) and bronze bushing (51) into housing tube (55). 1.
Support ball bearing (8, Figure 3-10) inner race and press eccentric (7) into bore. Install small retaining rings (6). 11. Install housing tube assembly onto pump housing (46). Be certain reciprocating tube (21) is inserted through both bushings. Using a .75 in. (19 mm) diameter rod through the inlet holes at bottom of tube, tighten to 20 - 25 ft. lbs. (27.1 - 33.9 N.m) torque. 2. Assemble crankrod assembly parts; large retaining rings (4), inner weights (3), outer weights (2) and install flat head screws (1). Tighten to 100 - 110 in. lbs. (11.3 - 12.4 N.m) torque. 3. Using a new O-ring (10), install install plunger tube (11) on outlet pin (9). Tighten to 100 - 110 in. lbs.
(11.3 - 12.4 N.m) torque. 12. Install shovel plug (56) and retainer (57). 13. Install new backup rings (47), O-rings (48 & 49), and outlet pin nuts (50). Tighten to 30 - 35 ft. lbs. (40.7 - 47.5 N.m) torque. 4. Assemble the wrist pin anchor (14), backup washer (15), cup seal (16) and plunger link rod (17) onto plunger tube (11). Tighten to 100 - 110 in. lbs. (11.3 - 12.4 N.m) torque. 14. Install gasket (41) and motor (42) on pump housing (46). Install washers (43) and socket head screws (44). 5. Assemble spring (18), ball (19), and plunger (20) on plunger link rod (17). Tighten plunger to 100 - 110 in. lbs. (11.3 - 12.4 N.m) torque. 15. Install shovel plug (56) in housing tube (55).
Install retaining ring (57). 6. Install reciprocating tube (21) onto wrist pin anchor (14). Tighten to 20 - 25 ft. lbs. (27.1 - 33.9 N.m) torque. 16. Install gasket (31), cover (30) and six self-tapping screws (29), on pump housing. 7. Install cup seal (22), O-ring (23), cylinder (24), ball cage (25), ball (26), O-ring (27) and check seat (28) into reciprocating tube (21). Tighten check seat housing to 20 - 25 ft. lbs. (27.1 - 33.9 N.m) torque. 17. Using new O-rings (40), install manifold (37) on motor (42). Install socket head screws (33). 18.
With the pump assembly in its normal operating position, add SAE 10W-30 motor oil to pump hous- ing until oil is level with bottom of pipe plug (45) hole. Install pipe plug.