honda — Electrical Equipment

16. ELECTRICAL EQUIPMENT BF40A-BF50A ~~ 2. POWER COIL 4. INDICATOR 3. ECT (Engine Coolant Temperature) SENSOR 1. CDI UNIT - 1. CDI UNIT (t4-J LLt used) a. INSPECTION Measure the resistance between the terminals and be sure that the measurements conform to the ranges shown in the table below. Use a tester that is equivalent to or higher than the performance specified; Internal resistance: 20 kQNDC, 9 WVAC Be careful not to touch the metallic part of the tester probe with your body, otherwise correct resistance value cannot be obtained. Read the tester manufacturer's operation instructions carefully before operation with a tester.

Be sure the tester's battery is fully charged and check the meter before using the tester. Use a R x 1 scale of an commercially available multi- meter, and meter shows current flowing from negative (-) to positive (+). *14 (Not used) [2] unit: kQ 1 2 3 *4 *5 6 *7 8 9 10 11 12 13 *14 15 16 17 18 19 20 21 22 T v n (I, 2 a z c v) I-" - d Y 36-150170-3001 14-60 150-2001 - 120-90 1 00 116-70 18.5-34/\1 8.5 - 34 I 10 - 40 17-70 115-60 I 1.4-6 111-50 I m 14.6-191 m 1 2-8.5 10.4-1.8/ 03 I\ 1 .

I 18-80130-15015.5-24124-1001 00 1 4 - 1 6 [ 00 1 7 - 2 8 1 3 - 1 3 1 m 12.4-101 16-70 30-150 5.5-24 24-100 m 3.6-15 00 7 - 2 8 3 - 1 3 00 2.4-10 7 - 2 8 60-300 m 90-400 15-60 60-300 m 22-100 m 17-70 9.5-38 m 9 - 3 6 14-60 00 m m m m m m 00 00 00 m 60-300 20-150 24-150 90-400 15-60 60-300 m 22-100 m 17-70 9.5-38 m 9 - 3 6 14-60 30-150 7 - 2 8 22-90 m 11 -45 m 8 - 3 2 4.8-20 m 4.4-17 5 - 2 0 26-150 7 - 2 8 22-90 m 11 -45 m 8 - 3 2 4.8-20 m 4.4-17 5 - 2 0 20-90 119-80 13.8-161 16-70 I m I 7 - 2 8 1 m 14.6-1812.2-9.5j m I 1.8-8 12.4-101 m 26-150 7 - 2 8 22-100 m 11 -45 03 8 - 3 2 4.8-20 m 4.4-18 5 - 2 0 15-60 1.4-6 11 -50 - 4.2-17 ~0 2-8.5 0.4-1.8 m 0 0.4 - 1.6 m m m m m m 00 00 m 00 m 24-150 16-70 16-70 115-60 I 1.4-6 111-50 I m 14.2-171 00 12-8.5 10.4-1.8/ m I 0 10.4-1.6 2 2 - 9 0 1 2 2 - 9 0 1 5 - 2 0 118-601 m 18.5-341 m 1 6 - 2 4 12.8-121 m 12.6-1113.2-13 16-1