OM1200 02/11 Torque Tables And Conversion Charts - Section 12 Page 12-1 TORQUE TABLES AND CONVERSION CHARTS This manual provides dual dimensioning for many specifications. Metric units are specified first, with U.S. standard units in parentheses. When torque val- ues are not specified in the assembly instructions contained in this manual, use the standard torque value for the hardware being used. Standard value torque tables are contained in this chapter for metric and SAE hardware. References throughout the manual to standard torques or other standard values will be to one of the following tables. Do not use standard values to replace specific torque values in assembly instructions. NOTE:
This truck is assembled with both metric and SAE (U.S.) hardware. Reference the correct table when determining the proper torque value. For values not shown in any of the charts or tables, standard conversion factors for most commonly used measurements are provided in the following tables. INDEX OF TABLES TABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page TABLE 1 Standard Tightening Torque For Metric Cap screws and Nuts . . . . . . . . . . . . . . . . . . . . . . . . . 12-2 TABLE 2 Standard Tightening Torque For SAE Grade 5 & 8 Cap Screws and Nuts . . . . . . . . . . . . . .
. . 12-3 TABLE 3 Standard Tightening Torque 12-Pt, Grade 9, Cap Screws (SAE) . . . . . . . . . . . . . . . . . . . . . . . 12-4 TABLE 4 Tightening Torque for T-Bolt Type Hose Clamps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-5 TABLE 5 Standard Tightening Torque For Split Flange Clamp Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-5 TABLE 6 Tightening Torque For Flared Tube And Hose Fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-5 TABLE 7 JIC 37° Swivel Nuts Torque Chart (SAE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-6 TABLE 8 Pipe Thread Torque Chart (SAE) . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-6 TABLE 9 O-Ring Boss Torque Chart (SAE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-7 TABLE 10 O-Ring Face Seal Torque Chart (SAE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-7 TABLE 11 Common Conversions Multipliers - Metric -to- English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-8 TABLE 12 Common Conversions Multipliers - English -to- Metric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-9 TABLE 13 Temperature Conversions. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . 12-10