. MAINTENANCE OUTLINE OF SERVICE 4 - 5 FUEL To prevent the moisture in the air from conden sing and forming water inside the fuel tank, always fill the fuel tank after completing the day's work. f fuel containing water or dirt is used, it cannot work properly. when storing or adding fuel. ure in the Operation and Maintenance Manual. The fuel pump is a precision instrument, and i f fuel containing water or dirt is used, it cannot work properly. Be extremely careful not to let impurities get in Always use the fuel specified for the temperat If the fuel is used at temperatures lower than °C (5°F), the fuel will solidify.
If the fuel is used at temperatures higher th result in problems such as a drop in output If the fuel is used at temperatures lower than the specified temperature (particularly at temperatures below -15 If the fuel is used at temperatures higher th an the specified temperature, the viscosity will drop, and this may . Before starting the engine, or when 10 minutes have passed after adding fuel, drain the sediment and water f rom the fuel tank. If the engine runs out of fuel, or if the filters ha ve been replaced, it is necessary to bleed the air from the circuit. If there is any foreign material in the fuel tank, wash the tank and fuel system.
Use low sulfur fuel or ultra low sulfur fuel only. NOTICE Always use diesel oil for the fuel. To ensure good fuel consumption characteristics and exhaust gas characteristics, the engine mounted on this machine use s an electronically controlled high-pressure fuel injection d evice. This device requires high precision parts and lubrication, so i f low viscosity fuel with low lubricating ability is used, the d urability may drop markedly. COOLANT AND WATER FOR DILUTION enting corrosion as well as preventing freezing. ue, the use of antifreeze coolant is essential. u Supercoolant (AF-NAC).
Komatsu Supercoolant (AF-NAC) has The coolant has the important function of prev Even in the areas where freezing is not an iss Komatsu machines are supplied with Komats u Supercoolant (AF-NAC). Komatsu Supercoolant (AF-NAC) has excellent anticorrosion, antifreeze and cooling propertiesand can be used continuously for 2 years or 4000 hours. As a basic rule, we do not recommend the (AF-NAC). If you use another coolant, it may aluminum parts of the cooling system. use of any coolant other than Komatsu genuine supercoolant cause serious problems, such as corrosion of the engine and ), there is no need to use a corrosion resistor. For details, see GE 4-22)". led water or tap water (soft water).
ater (hard water), contains large amounts of minerals (calcium, When using Komatsu Supercoolant (AF-NAC "CLEAN INSIDE OF COOLING SYSTEM (PA When diluting the antifreeze coolant, use distil Natural water, such as a river water or well w magnesium, etc.), and this makes it easier for s cale to form inside the engine or radiator. Once scale is deposited inside the engine or radiator, it is extremely difficult to remove. It also causes overheating due to poor heat exchange, so when you dilute the coolant, we recommend that you use water with an overall hardness of less ecautions given in the Operation and Maintenance Manual. keep it away from flame. differs according to the ambient temperature.
AN INSIDE OF COOLING SYSTEM (PAGE 4-22)". less than 100 PPM. When using antifreeze, always observe the pr Antifreeze coolant is flammable, so be sure to The ratio of Supercoolant (AF-NAC) to water For details of the ratio when mixing, see "CLE Even in areas where it is not necessary to pre vent freezing, use Supercoolant (AF-NAC) at a mixing ratio of at system. emix. In this case, never add diluting water. cool before adding coolant.
of at least 30% to prevent corrosion of the cooling Supercoolant (AF-NAC) may be supplied in pr If the engine overheats, wait for the engine to If the coolant level is low, it will cause overheati ng, and will also cause problems with corrosion due to air entering the coolant.