Perkins — Perkins 854E-E34TA and 854F-E34T Industrial Engines Operation and Maintenance Manual

80 SEBU8726-03 Maintenance Section Fuel Specification BTL and HVO fuels are considered to be low carbon fuels as they reduce carbon foot print compared to fossil fuels and are commonly referred to as renewable fuels. These fuels must not be confused with biodiesel FAME which is fundamentally different fuel and is discussed in a separate section in this manual. Supplemental diesel fuel additives are not generally recommended. This recommendation is due to potential damage to the fuel system or the engine. Your fuel supplier or the fuel manufacturer will add the appropriate supplemental diesel fuel additives.

Perkins recognizes the fact that additives may be required in some special circumstances. These paraffinic fuels have virtually no sulphur or aromatics and have very high cetane numbers which enable very clean burning and efficient engine operation. Chemically these fuels are similar to diesel fuel derived form petroleum and are therefore suitable to use in diesel engines as a replacement or blend stock with conventional diesel fuel. To be acceptable renewable and alternative fuels must meet latest edition of the paraffinic diesel fuel specification “CENTS 15940”.

The fuel should also meet requirements described in table 16 , Perkins Specification for Distillate Diesel Fuel, EN590, or latest ASTM D975 specification. Note: Some anti-corrosion additives can lead to injector fouling, this fouling can cause the injector to operate incorrectly. Contact your fuel supplier for those circumstances when fuel additives are required. Your fuel supplier can recommend the appropriate fuel additive and the correct level of treatment. Note: For the best results, your fuel supplier should treat the fuel when additives are required. The treated fuel must meet the requirements that are stated in table 16 .

Ensure that the fuel has got appropriate cold flow properties (cloud point and CFPP) for the minimum statistical ambient temperature the engine is expected to see in the operation. The Fuel must also meet lubricity requirements as specified in the lubricity section of this “Operation and Maintenance Manual” Fluid Recommendations Perkins Diesel Fuel System Cleaner Perkins T40-0012 Fuel Cleaner is the only fuel cleaner that is recommended by Perkins. If biodiesel or biodiesel blends of fuel are to be used, Perkins require the use of Perkins fuel cleaner. The use of the fuel is to remove deposits within the fuel system that is created with the use of biodiesel.

For more information on the use of biodiesel and biodiesel blends refer to “Recommendation for Biodiesel and Using B20”. Fuel for Cold-Weather Operation The European standard “EN590” contains climate dependant requirements and a range of options. The options can be applied differently in each country. There are five classes that are given to arctic climates and severe winter climates. 0, 1, 2, 3 and 4. Perkins fuel cleaner will remove deposits that can form in the fuel system with the use of biodiesel and biodiesel blends. These deposits can create a loss of power and engine performance. Fuel that complies with “EN590” CLASS 4 can be used at temperatures as low as −44 °C (−47.2 °F).

Refer to “EN590” fora detailed discretion of the physical properties of the fuel. Once the fuel cleaner has been added to the fuel, the deposits within the fuel system are removed after 30 hours of engine operation. For maximum results, continue to use the fuel cleaner for up to 80 hours. Perkins fuel cleaner can be used on an on-going basis with no adverse impact on engine or fuel system durability. The diesel fuel “ASTM D975 1-D” used in the United States of America may be used in very cold temperatures that are below −18 °C (−0.4 °F). Aftermarket Fuel Additives Details instruction on the rate of which the fuel cleaner must be use are on the container.

NOTICE Perkins does not warrant the quality or performance of non-Perkins fluids and filters. When auxiliary devices, accessories, or consum- ables (filters, additives) which are made by other manufacturers are used on Perkins products, the Perkins warranty is not affected simply because of such use. However, failures that result from the installation or use of other manufacturers devices, accesso- ries, or consumables are NOT Perkins defects. Therefore, the defects are NOT covered under the Perkins warranty.