Lubrication System/Drain Engine Oil and Remove Oil Pan LUBRICATION SYSTEM SPECIFICATIONS—CONTINUED TORQUES Oil Conditioning Housing-to-Cylinder Block: * Step 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 N·m (15 lb-ft) Step 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 N·m (27 lb-ft) Oil Pump: Drive Gear-to-Pump Drive Shaft Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 N·m (40 lb-ft) Pump Cover-to-Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
41 N·m (30 lb-ft) Intake Tube-to-Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 N·m (30 lb-ft) Pump Housing-to-Cylinder Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 N·m (35 lb-ft) Oil Pan: ** 3/8 in. Cap Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 N·m (50 lb-ft) 1/2 in. Cap Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 N·m (115 lb-ft) Oil Pan Drain Plug: Aluminum Pans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
102 N·m (75 lb-ft) Cast Iron Pans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 N·m (35 Lb-ft) * Refer to INSTALL OIL FILTER AND OIL CONDITIONING HOUSING, later in this group, for proper cap screw tightening sequence. ** Initially tighten all cap screws to 54 N·m (40 lb-ft), starting at right rear corner of oil pan (facing toward flywheel end) and proceed counterclockwise. Finish tightening cap screws to torques specified above, using the same sequence and tighten all 3/8 in. cap screws first. 20 2 RG,CTM42,G20,32-19-16AUG94 DRAIN ENGINE OIL AND REMOVE OIL PAN 1. Drain engine coolant. 2.
Disconnect turbocharger oil inlet line at turbocharger or oil conditioning housing. (See DISCONNECT TURBOCHARGER OIL INLET LINE, in Group 03.) 3. Drain engine oil. 4. Remove oil level sight gauge (if equipped). 5. Remove oil pan and discard gasket. CTM42 (24MAR95) 20-2 6076 Diesel Engines—S.N. (500000— ) S11,0404,C -19-04JUN93 160101 PN=205