. MAINTENANCE OUTLINE OF SERVICE 4 - 5 FUEL To prevent the m oisture in the air from condensing and formin g water inside the fuel tank, always fill the fuel tank after completing t he day's work. a precision instrument, and if fuel containing water or dirt is used, it cannot work properly. eful not to let impurities get in when storing or adding fuel. el specified for the temperature in the Operation and Maintenance Manual.
The fuel pump is a precision instrument, and if fuel containin g water or dirt is used, it cannot work pro Be extremely car eful not to let impurities get in when storing Always use the fu el specified for the temperature in the Oper If the fuel is us °C (5°F), the f If the fuel is us result in proble If the fuel is us ed at temperatures lower than the specified t emperature (particularly at temperatures below -15 uel will solidify. If the fuel is us ed at temperatures higher than the specified temperature, the viscosity will drop, and this may ms such as a drop in output.
Before starting th e engine, or when 10 minutes have passed a fter adding fuel, drain the sediment and w ater from the fuel tank. If the engine runs out of fuel, or if the filters have been replac ed, it is necessary to bleed the air from t he circuit. If there is any for eign material in the fuel tank, wash the tank and fuel system. NOTICE . Never use any other fuel. Always use diesel fuel The engine on this ma chine uses electronic control and high-pressure f uel injection equipment to enable it to provid e good fuel consumption and goo d exhaust gas characteristics. For this reason, hi gh-precision parts and lubricating ability are demanded.
Using low-viscosity fu el with poor lubricating ability will cause a marke d reduction in the durability of the engine. COOLANT AND WATER FOR DILUTION Komatsu genuine SUPERCOOLANT (AF-NAC) has the important function of preventing corrosion as well as preventing freezing. Even in the areas where freezing is not an issue, the use of antifreeze coolant is essential. Komatsu machines are supplied with Komatsu SUPERCOOLANT (AF-NAC). SUPERCOOLANT (AF-NAC) has excellent anticorrosion, antifreeze and cooling propertiesand can be used continuously for 2 years or 4000 hours. As a basic rule, we do not recommend the use of any coolant other than SUPERCOOLANT (AF-NAC).
If you use another coolant, it may cause serious problems, such as corrosion of the engine and aluminum parts of the cooling system. When using antifreeze, always observe the precautions given in the Operation and Maintenance Manual. Coolant is already diluted with distilled water, so it is not flammable. The density used for the coolant differs according to the ambient temperature. For details of the density of the coolant, see "CLEAN INSIDE OF COOLING SYSTEM (PAGE 4-28)". Even in the areas where it is not considered necessary to prevent freezing, always use coolant with a density of over 30% in order to prevent corrosion of the cooling system.
coolant is diluted with distilled water that does not contain any ions or water-hardening substances. Never dilute the coolant with ordinary water. If the engine overheats, wait for the engine to cool before adding coolant. Komatsu genuine preventing freezi Even in the areas where freezing is not an issue, the use of a Komatsu machin es are supplied with Komatsu SUPERCOOL ANT (AF-NAC). SUPERCOOLANT (AF- NAC) has excellent anticorr osion, antifreeze and cooling propertiesand c an be used continuously for 2 years or 40 00 hours. As a basic rule, w e do not recommend the use of any coolant o ther than SUPERCOOLANT (AF-NAC). If you use another coolant, cooling system.
it may cause serious problems, such as corrosion of the engine and aluminum parts of the eeze, always observe the precautions given in the Operation and Maintenance Manual. y diluted with distilled water, so it is not flammable. for the coolant differs according to the ambient temperature. density of the coolant, see "CLEAN INSIDE OF COOLING SYSTEM (PAGE 4-28)".
When using antifr eeze, always observe the precautions give n in the Operation and Maintenance Man Coolant is alread y diluted with distilled water, so it is not flam The density used for the coolant differs according to the amb For details of the density of the coolant, see "CLEAN INSIDE Even in the areas where it is not considered necessary to pre vent freezing, always use coolant with a density of over 30% in orde r to prevent corrosion of the cooling system. coolant is diluted with distilled water that does not contain any ions or water-hardening substances. Ne ver dilute the coolant with o rdinary water. heats, wait for the engine to cool before adding coolant.
If the engine over heats, wait for the engine to cool before ad If the coolant leve l is low, it will cause overheating, and will als o cause problems with corrosion due to ai r entering the coolant.