Case IH AFX8010 — CLEANING Primary cleaning

CROP PROCESSING - CLEANING Primary cleaning B. If no continuity is found, continue with step 10 . NOTE: The CCM module connects both sides of the circuit to ground when in neutral to "lock" the actuator in position, irregardless of key switch position, as long as it receives power through fuse F-22. This ground path may be used to test for an open circuit condition. 10. Disconnect connector X023 . Use a multimeter to check for continuity between the front frame (FF) harness end of connector X023 pin 1 and chassis ground. There should be continuity. A.

If continuity is found, there is an open circuit in the lower frame (LF) harness between connector X023 pin 1 and connector X088 pin E wire 707 grey. Locate the open and repair. B. If no continuity is found, there is an open circuit in the front frame (FF) harness between connector X023 pin 1 and connector X020 pins J3-19 and J3-20 on one of the following wires; wire 707 grey, connector X023 pin 1 to FF harness splice, wire 705 grey, harness splice to connector X020 pin J3-19, or wire 706 grey, harness splice to connector X020 pin J3-20. Locate the open and repair. 11. Disconnect connector X088 . Use a multimeter to check from continuity between connector X088 pin D and chassis ground.

There should be continuity to ground. A. If no continuity is found, continue with step 12 . B. If continuity is found, recheck the motor for continuity as indicated at step 8 . 12. Disconnect connector X023 . Use a multimeter to check for continuity between the front frame (FF) harness end of connector X023 pin 2 and chassis ground. There should be continuity. A. If continuity is found, there is an open circuit in the lower frame (LF) harness between connector X023 pin 2 and connector X088 pin D wire 710 white. Locate the open and repair. B.

If no continuity is found, there is an open circuit in the front frame (FF) harness between connector X023 pin 2 and connector X020 pins J3-39 and J3-40 on one of the following wires; wire 710 white, connector X023 pin 2 to FF harness splice, wire 708 white, harness splice to connector X020 pin J3-39, or wire 709 white, harness splice to connector X020 pin J3-40. Locate the open and repair. 13. If the shoe leveling actuator does not operate in either direction, and there are no fault codes indicated, the supply power for the circuit may not be present. Remove and inspect fuse F-22. A. If the fuse has failed, continue with step 14 . B. If the fuse is okay, continue with step 15 . 14.

If fuse F-22 has failed, replace the fuse. A. If the fuse immediately fails, there is a short to ground in the cab main (CM) or front frame (FF) harnesses in one of the following wires; wire 024 red, from the fuse panel through connector X031 pin 16 to front frame (FF) harness splice, wire 700 red, harness splice to connector X020 pin J3-29 on CCM1 module, or wire 701 red, harness splice to connector X020 pin J3-30 on CCM1 module. Locate the short to ground and repair. 15. Carefully remove connector X020 from the bottom of the CCM1 module. Use a multimeter to check for voltage on the harness end of connector X020 pins J3-29 and J3-30. There should be 12 volts . B.

If the fuse is okay, continue with step 15 . A. If there is no voltage, there is an open circuit in the cab main (CM) or front frame (FF) harnesses in one of the following wires; wire 024 red, from the fuse panel through connector X031 pin 16 to front frame (FF) harness splice, wire 700 red, harness splice to connector X020 pin J3-29 on CCM1 module, or wire 701 red, harness splice to connector X020 pin J3-30 on CCM1 module. Locate the open and repair. After repair, continue with step 16 . B. If there is 12 volts , continue with step 16 . 16. Carefully remove connector X020 from the bottom of the CCM1 module.

Use a multimeter to check for continuity between the harness end of connector X020 pins J3-9 and J3-10 and chassis ground. There should be continuity to ground. 9717 1 27/05/2004 K.62.B / 93