DISTRIBUTION SYSTEMS - LIGHTING SYSTEM Head light - Overview (A.40.A.11 - C.10.A.10) AFX8010 DESCRIPTION The road lights E-13/E-14 are used only on European configuration combines, and are controlled by the road light switch S-26, which is mounted on the steering column. The road lights E-13/E-14 are dual beam lights, with both low beam and high beam filaments. POWER SUPPLY Wiring harness - Electrical schematic frame 27 (A.30.A.88 - C.20.E.27) Wiring harness - Electrical schematic frame 36 (A.30.A.88 - C.20.E.36) Current from the Cab Power Relay K-26 travels across the electrical system buss bar to reach fuse F-49.
Current passes through fuse F-49 and a wire splice to reach connector X256 pin 5 of the Road Light Switch (S-26), which supplies power for the marker and road lights circuits. Rotating the Road Light Switch (S-26) to the second position will activate the marker lights alone (refer to Marker light - Overview (A.40.A.12 - C.10.A.10) for more information), while the third position will activate both the marker lights and the road lights. When the road light switch is rotated to the third position, current may cross from pin 5 to reach pin 4 or pin 7, depending on the fore and aft position of the road light switch.
Pulling the road light switch stalk toward the operator (low beam position) will result in current exiting pin 7, while pushing the stalk away from the operator (high beam position) will result in current exiting pin 4. If the road light switch stalk is pulled firmly past the low beam position toward the operator, a momentary contact will also provide power to pin 4 (high beam flash). LOW BEAM OPERATION Wiring harness - Electrical schematic frame 36 (A.30.A.88 - C.20.E.36) Current flows from connector X256 pin 7 to reach pin 1 of the low beam relay (K-05). The ground path of the relay exits pin 2 and travels to the cab floor ground location #3.
This causes the low beam relay to energize and latch pin 3 to pin 5. Current passes through the low beam fuse F-33 to the low beam relay pin 3, through the relay, and continues through connector X005 pin 13 to reach a wire splice. From here current flows to the LH road light E-13 connector X164 pin B and RH road light E-14 connector X169 pin B. Wires from pin C of each light go to the front frame ground #2, causing both lights to illuminate. HIGH BEAM OPERATION Wiring harness - Electrical schematic frame 36 (A.30.A.88 - C.20.E.36) Current flows from connector X256 pin 4 to reach pin 1 of the high beam relay (K-04).
The ground path of the relay exits pin 2 and travels to the cab floor ground location #3. This causes the high beam relay to energize and latch pin 3 to pin 5. Current passes through the high beam fuse F-32 to the high beam relay pin 3, through the relay, and continues through connector X005 pin 10 to reach a wire splice. From here current flows to the LH road light E-13 connector X164 pin A and RH road light E-14 connector X169 pin A. Wires from pin C of each light go to the front frame ground #2, causing both lights to illuminate.
FLIP-UP LIGHTS CIRCUIT Wiring harness - Electrical schematic frame 36 (A.30.A.88 - C.20.E.36) Wiring harness - Electrical schematic frame 37 (A.30.A.88 - C.20.E.37) The flip-up lights are designed for use with flip-up headers. The flip-up light (FC) harness plugs into the main frame (MF) harness at the existing road lights E-13 & E-14. The flip-up lighting consists of marker lights, road lights, and two relays. The flip up lighting is controlled by the road light switch S-26 in the same manner as the standard marker lights and road lights. A wire in the flip-up header (HH) harness (box V, Frame 37) provides the ground path for the flip-up low beam and high relays.
When a flip-up head is attached to the combine, the relays will be energized to send current to the flip up lights instead of the standard road lights. This wire is not present in other header (HH) harnesses, so when other headers are installed, the standard road lighting will function instead of the flip-up lights. 9668 1 27/05/2004 A.40.A / 9