Yanmar — Yanmar Diesel Inboard Shop Manual for One, Two, and Three Cylinder Engines

FUEL INJECTION AND GOVERNOR SYSTEMS 157 the nut (42), then withdraw the shaft. Determine if the shaft, the timing gearcase or both are worn. Replace or re- pair any worn parts. 7B. On 2GM, 2GM20, 3GM, 3GM30, 3HM and 3HM35 models-Check the stop shaft (5, Figure 48) for exces- sive play between the shaft and the timing gearcase. If ex- cessive play is evident, drive out the taper pin (6) by driving against the small end of the pin. Remove the lock- ing screw (7). Remove the nut (42), then remove the shaft. Determine if the shaft, the timing gearcase or both are worn. Replace or repair any worn parts. 8. Inspect the governor springs for damage and distor- tion.

Measure the length of the main and secondary gover- nor springs as shown in Figure 49. Replace either spring if its free length dimension is not as specified in Table 2. If either spring is questionable, take it to a Yanmar dealer- ship for testing. 9. Remove and inspect the thrust collar (32, Figure 47 or Figure 48). Replace the thrust collar if damaged or if the thickness is less than 2.9 mm (0.114 in.). 10. Remove the thrust bearing (33, Figure 47 or Figure 48). Replace the bearing if damaged. 11. Remove the governor sleeve (34, Figure 47 or Fig- ure 48). Inspect the governor sleeve and crankshaft for damage. Refer to the specifications in Table 3. 12.

Check the operation of the flyweight assembly (37, Figure 47 or Figure 48). The flyweights should move smoothly without excessive looseness. The contact sur- face in the flyweight groove should not be excessively worn. The flyweight assembly must be replaced as a com- plete assembly. Remove the crankshaft nut as described in Chapter Five or Six to remove the flyweight assembly. 13. Reassemble the governor assembly by reversing the disassembly procedure while noting the following: a. Do not distort the governor springs during installa- tion. b. Install the governor springs so the long hook end engages the speed control lever (12, Figure 47 or Figure 48). c.

Install the secondary governor spring (14, Figure 47 or Figure 48) so the lower end of the spring fits in the loop on the main governor spring. d. Note that the pins securing the levers on the shafts are tapered. The lever should fit tightly on the shaft after the pin is installed. If not, replace the worn part. e. Check the movement of all the parts after assembly. Motion should be smooth without binding. 14. Reinstall the timing gearcase as described in Chapter Five for single cylinder engines or Chapter Six for multi- cylinder engines. L1 MAIN GOVERNOR SPRING L1 SECONDARY GOVERNOR SPRING 4.

If disassembly of the governor shaft assembly is re- quired, remove the retaining bolts (29, Figure 47 or Fig- ure 48) and remove the shaft assembly. To disassemble the components, detach the snap ring (16), then drive out the tapered pins that retain the levers. Replace the worn parts. 5. Remove the idle adjuster bracket and side cover (4, Figure 47 or Figure 48). 6. Check the speed control lever and shaft (12, Figure 47 or Figure 48) for excessive play between the shaft and the timing gearcase and between the lever and the shaft. a. If the shaft is loose in the timing gearcase, remove the nut (1, Figure 47 or Figure 48), then remove the speed control lever (3).

Remove the shaft (12) and determine if the shaft, the timing gearcase or both are worn. Replace or repair the worn part. b. If the lever is loose on the shaft, remove the nut (1, Figure 47 or Figure 48), then remove the speed control lever (3). Determine if the lever, the shaft or both are worn. Replace any worn parts. 7A. On IGM and IGMIO models-Check the stop shaft (5, Figure 47) for excessive play between the shaft and the timing gearcase. If excessive play is evident, remove