Available INSITE™ Electronic Service Tool Trimmables R2.8 CM2220 R101B Page 2-8 Section 2 - Start-Up and Troubleshooting Fault Code Troubleshooting Manual. See the User Interface Display guide, Part Number 5467023, included in the R2.8 CM2220 R101B Engine Kit for instructions on using the dash display. Mass Air Flow Offset Correction (392-001) General Information The R2.8 CM2220 R101B calibration contains a feature that allows the user to auto-calibrate the mass air flow (MAF) sensor to the specific air intake setup. This allows the sensor to accurately read fresh air flow into the engine and calculate the appropriate ratio of exhaust gas recirculation (EGR).
Even when using the intake setup described in Procedure 388-017 in Section 1 (Air Intake System), it is still recommended to complete the MAF-Offset Correction sequence to properly calibrate the MAF sensor. The calibration sequence is initiated via a pedal dance. Coolant temperature must be greater than 70°C [158°F] for the sequence to initiate. This can be monitored via the J1949 Dash Display. 1 Turn vehicle off for 10 seconds 2 Press accelerator pedal to the floor, key the vehicle on, and continue depressing the pedal for 3 seconds 3 Release accelerator pedal for 3 seconds 4 Depress the accelerator pedal and hold for 5 seconds.
Start the vehicle (pedal remains pressed to the floor) If the engine speed instantly revs up, the process did not initiate properly 5 Continue holding pedal to floor while engine performs calibration sequence. Engine speed will step up from idle to 3000 rpm in 200 rpm increments, and then reduce back to idle If the engine speed stays at idle, the vehicle is in calibration mode 6 Once complete, continue holding pedal at idle for 10 seconds. Release pedal. Key vehicle off for at least 1 minute to save new calibration. An engine speed blip will be seen/heard.
Available INSITE™ Electronic Service Tool Trimmables (392-002) General Information Fast Idle Warm Up Fast Idle Warm Up feature enables the engine to increase idle speed for a pre-determined amount of time, based on coolant temperature. The raised idle speed assists with the rate at which the engine warms up in cold ambient temperatures. The Fast Idle Warm Up feature is available to turn ON via INSITE™ electronic service tool. It is defaulted OFF in the mainline calibration, but is available to be set to ON. There is a 30 second delay before the feature is enabled, engine speed is ramped from 800 rpm to 1250 rpm at a rate of 50 rpm/s.
The feature is enabled at a coolant temperature below 10°C [50°F] and deactivates at or above 20°C [68°F]. It also deactivates upon accelerator pedal application. Vehicle Speed Vehicle speed can be calculated by the engine control module (ECM) and broadcast on the J1939 CAN network for use with aftermarket gauges. The Vehicle Speed feature is available to trim via INSITE™ electronic service tool. It is defaulted to None in the mainline calibration, but is available to be set to either Magnetic or Data Link - Tailshaft. Tire size, in rev/km, as well as rear axle ratio (RAR) need to be trimmed with INSITE™ electronic service tool as well.
Should a hardwired vehicle speed sensor be necessary, Pin J2-40 in the ECM wiring is required to be moved to pin J2-28. Idle Adjustment Low Speed Idle is selectable via INSITE™ electronic service tool, between 700 and 1100 rpm in 25 rpm increments. It is defaulted to 800 rpm for the optimal noise, vibration, and harshness (NVH). The R2.8 CM2220 R101B also offers a temporary idle increment/decrement option, where the user can temporarily raise or lower idle speed to better facilitate the operation of additional accessories. Should this feature be desired, it is required to wire switches to ECM pins J2-24 (Increment) and J2-37 (Decrement).
To buy Cummins Parts and Service Manuals, Training Guides, or Tools go to our website at https://store.cummins.com