Cummins — Cummins CM2220 R2.8 Installation Guide R101B

R2.8 CM2220 R101B Fuel Recommendations and Specifications Section V - Maintenance Specifications Page V-3 Fuel Recommendations and Specifications Fuel Recommendations WARNING Do not mix gasoline, alcohol, or gasohol with diesel fuel. This mixture can cause an explosion. CAUTION Due to the precise tolerances of diesel injection systems, it is extremely important that the fuel be kept clean and free of dirt or water. Dirt or water in the system can cause severe damage to both the fuel pump and the fuel injectors. Lighter fuels can reduce fuel economy or possibly damage fuel system components.

CAUTION For engines optimized for use with an aftertreatment system to meet the Euro IV emission regulations. In order to meet theses regulations, with a maximum sulfur content of 50 ppm is required for correct operation of the aftertreatment system. By not doing so can permanently damage the engine and aftertreatment systems within a short period of time. This damage could cause the engine to become inoperable and affect the warranty coverage on the engine. Cummins Inc. engines without exhaust aftertreatment should only be operated with diesel fuel containing less than 5,000 ppm sulfur content. Cummins Inc.

recommends the use of American Society of Testing and Materials (ASTM) number 2D fuel. The use of number 2D diesel fuel will result in optimum engine performance. Cummins Inc. recommends the use of ASTM number 2D fuel. The use of number 2D diesel fuel will result in optimum engine performance. At operating temperatures below 0°C [32°F], acceptable performance can be obtained by using blends of number 2D and number 1D. The following chart lists acceptable substitute fuels for this engine. 1 Any adjustment to compensate for reduced performance with a fuel system using alternate fuel is not warrantable.

2 Winter blend fuels, such as found at commercial fuel dispensing outlets, are combinations of number 1D and number 2D diesel fuel and are acceptable. 3 British Thermal Unit (BTU) Content/Degree American Petroleum Institute (API) Gravity - Low API gravity fuels have a higher thermal energy content (BTU). As a general rule of thumb, there is a 3 to 5 percent decrease in BTU content for every 10 degree increase in API gravity. There is also a 0.7 degree API gravity increase with an increase in fuel temperature. This decrease in energy content equates roughly to the same percentage of power loss. Use of fuels with higher API gravity will cause higher than normal fuel consumption. NOTE:

Cummins Inc. recommends that the cetane number of diesel fuel be a minimum of 45 for engines that are expected to operate at temperatures below 0°C [32°F] and a minimum of 40 for engines that are operated at temperatures above 0°C [32°F]. NOTE: Using a diesel fuel with a lower than recommended cetane number can cause hard starting, instability, and excessive white smoke. To maintain satisfactory operation at low ambient temperatures, it is important to specify diesel fuel of the correct cetane number. NOTE: Cummins Inc. requires all permissible fuels to have adequate fuel lubricity.

This means the Ball On Cylinder Evaluator (BOCLE) number is 3100 or greater as measured by ASTM specification D6078, Scuffing Load Ball On Cylinder Evaluator (SLBOCLE). Lubricity can also be measured by ASTM specification D6079, ISO 12156, High Frequency Reciprocating Rig (HFRR) in which the fuel must have a wear scar diameter of 0.45 mm [0.02 in] or less.

To buy Cummins Parts and Service Manuals, Training Guides, or Tools go to our website at https://store.cummins.com Acceptable Substitute Fuels - Cummins® Fuel System Number 1D Diesel(1) (2) Number 2D Diesel(2) Number 1K Kerosene Jet-A Jet-A1 JP-5 JP-8 Jet-B JP-4 CITE OK OK Not OK Not OK Not OK Not OK Not OK Not OK Not OK Not OK 48-34(3) 40-24(3) 50-35(3) 51-37(3) 51-37(3) 48-36(3) 51-37(3) 57-45(3) 57-45(3) 57-45(3)