Mitsubishi — Mitsubishi Diesel Engine Service Manual

SERVICE STANDARDS 1. Service Standards Table Unit: mm (in.) 1 - 12 Group Item Nominal value Standard value Limit Remarks Engine general Max. speed (based on the rated speed) +30 2700 min-1 -10 Min.

speed 1000±25 min-1 Compression pressure (at 290 min-1) 2.9 MPa (30 kgf/cm2) [421 psi] or above 2.6 MPa (27 kgf/cm2) [377 psi] or less Both oil and coolant temperatures at 20 to 30℃ (68 to 86°F) Engine oil pressure Rated speed 0.29 to 0.39 MPa (3.0 to 4.0 kgf/cm2) [42.07 to 56.57 psi] Oil temperature at 60 to 95℃ (140 to 194°F) Low idle speed 0.098 MPa (1.0 kgf/cm2) [14.22 psi] Valve timing [with 2 mm (0.079 in.) clearance on the valve side; cold engine] Inlet valve open BTDC 15° The theoretical valve timing figures for inspection vary from the actual valve timing.

Inlet valve closed ABDC 41° Exhaust valve open BBDC 54° Exhaust valve closed ATDC 10° Valve clearance Inlet valve 0.25 (0.01) Cold engine Exhaust valve 0.25 (0.01) Fuel injection timing (BTDC) 17° Engine main parts Rocker Rocker arm inner diameter φ19 (0.749) 18.910 to 18.930 (0.7450 to 0.7458) ― Rocker shaft diameter φ19 (0.749) 18.880 to 18.898 (0.7438 to 0.7445) ― Arm-to-shaft clearance (oil clearance) 0.012 to 0.050 (0.0004 to 0.0019) 0.200 (0.0079) Replace rocker arm.

Valve Valve stem diameter Inlet φ6.6 (0.260) 6.565 to 6.580 (0.2586 to 0.2592) 6.500 (0.256) Exhaust φ6.6 (0.260) 6.530 to 6.550 (0.2572 to 0.2580) 6.500 (0.256) Valve guide inner diameter Inlet φ6.6 (0.260) 6.600 to 6.615 (0.2600 to 0.2606) Exhaust φ6.6 (0.260) 6.600 to 6.615 (0.2600 to 0.2606) Valve stem-to-guide clearance Inlet 0.020 to 0.050 (0.0008 to 0.0020) 0.100 (0.004) Replace valve and valve guide.

Exhaust 0.050 to 0.085 (0.0020 to 0.0033) 0.150 (0.006) Valve seat and valve Valve seat angle 45° Valve seat width Va lve sea Valve head sinkage 0 1.6 0.25 to 0.75 (0.0098 to 0.0295) 1.30 to 1.80 1.5 (0.0591) 2.5 Valve seat width (0.063) 1.5 (0.0512 to 0.0709) 1.35 to 1.65 (0.0985) 0.5 V se alve at V alve head Valve head Valve head margin Installed valve guide protrusion (0.0591) 10 (0.394) (0.0531 to 0.0650) 9.5 to 10.5 (0.3743 to 0.4137) (0.0197) ― angle sinkage margin