Perkins — Perkins 4.108 4.107 4.99 Diesel Engine Workshop Manual

ENGINES FOR REFRIGERATION UNITS-R.3 A later controlled expansion piston with a 0.020 in (0.50 mm) off-set gudgeon pin has been introduced and details of these are given on Pages B3. B.4. F.2 and F.3. Timing Gear Cover and Oil Seal Early engines use a black nitrile or a red silicone seal in a timing gear cover of pressed steel. An oil thrower is used with a nitrile seal, but a spacer is used in place of the oil thrower with the silicone seal. The silicone seal has a series of spiral grooves set into the front face of the main lip and a shaft rotation arrow marked on the front face of the seal. This type of seal is known as a 'Spiroseal'. There is also a dust lip forward of the main lip.

A controlled expansion piston has been introduced into the 4.108 refrigeration specification engine. These pistons have a closer tolerance to the cylinder bore. therefore extreme care must be taken during handling. storing and refitting as any distortion or damage to the piston skirt could lead to a seizure. Later engines use a red or brown silicone 'Spiroseal' in a timing gear cover of cast aluminium which is dowelled to ensure centralisation of the seal. The crankshaft pulley has been lengthened and the oil thrower or spacer has been removed. An interim controlled expansion piston was introduced from Engine No. 108U113592 and a final specification piston from Engine No. 108U119423.

The final specifica- tion piston will be the only one supplied as a spare part. and when used as a replacement for the interim or the older type five ring piston. they should only be fitted in complete engine sets using the correct piston ring pack. The latest engines have a wear ring fitted to the crankshaft pulley and use a black viton seal which has a larger internal diameter. The latest viton seal is a 'Spiroseal' with a protruding dust lip. For information on fitting the oil seal and timing gear cover refer to page J.1. Details of the controlled expansion pistons and their respective ring layouts are as follows: - Piston Type Piston Height in Relation to Cylinder Block Top Face ...

Bore Dia. for Gudgeon Pin Compression Ring GroOve Width - Top Compression Ring Groove Width - 2nd & 3rd Oil Control Ring Groove - 4th Flat Topped - Controlled Expansion 0.002/0.006 in (0,05/0.15 mm) above 1.0627/1.0629 in (26.994/26.999 mm) 0.080/0.083 in (2,03/2.10 mm) 0.064/0.065 in (1.64/1.65 mm) 0.188/1.189 in (4,79/4,81 mm) Piston Rings Top Compression (marked 'TOP') ... Second and Third Compression (marked 'BTM') Fourth Oil Control Top Compression Ring Width Ring Clearance in Groove Second and Third Compression Ring Width ...

Ring Clearance in Groove Fourth Scraper Ring Width Ring Clearance in Groove Ring Gap Top Compression Ring Gap Second and Third Compression Ring Gap Fourth Scraper Chrome Plated Taper Faced Internally Stepped Spring Loaded Scraper 0.077/0.078 in (1.96/1,98 mm) 0.003/0.005 in (0.08/0.13 mm) 0.0615/0.0625 in (1.56/1.59 mm) 0.0015/0.0035 in (0.04/0.09 mm) 0.186/0.1865 in (4.72/4.74 mm) 0.002/0.0035 in (0.05/0.09 mm) 0.012/0.020 in (0.30/0.50 mm) 0.009/0.017 in (0.23/0,43 mm) 0.010/0.018 in (0.25/0,46 mm)