G1,2.indd (FR)

SECTION 4 ELECTRICAL SYSTEM SECTION 4 ELECTRICAL SYSTEM Group 1 Component Location - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-1 Group 2 Monitoring system - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-3 Group 3 Electrical Circuit - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-9 Group 4 Electrical Component Specification - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-25 Group 5 Connectors - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-31

Стр. 1

SECTION 4 ELECTRICAL SYSTEM SECTION 4 ELECTRICAL SYSTEM GROUP 1 COMPONENT LOCATION GROUP 1 COMPONENT LOCATION 1. LOCATION 1 1. LOCATION 1 1 2 3 4 5 6 13 12 7 Switch panel 2 8 Switch panel 3 Switch panel 1 VOLUME VOLUME - + 1 2 3 4 5 TA HYUNDAI SOURCE RDS BAND AST Location at inside of battery cover 14 15 16 17 9 18 10 11 RH LH 35Z9A4EL02 1 Start switch 2 Cigar lighter 3 Overload switch 4 Quick clamp switch 5 Travel alarm switch 6 Auto idle switch 7 Washer/wiper switch 8 Heater switch 9 Master switch 10 Horn switch 11 Travel speed control switch 12 Main light switch 13 Beacon switch 14 Speaker 15 Radio & USB player 16 Accel dial switch 17 Relay board assy 18 Fuse box 4-1 4-1

Стр. 2

2. LOCATION 2 2. LOCATION 2 5 7 8 9 4 1 2 3 6 35Z9A4EL22 1 Work lamp 2 Horn 3 Battery 4 Master switch 5 Fuel sender 6 Travel alarm buzzer 7 Engine oil pressure switch 8 Air cleaner pressure switch 9 Water temperature sender 4-2 4-2

Стр. 3

GROUP 2 MONITORING SYSTEM GROUP 2 MONITORING SYSTEM The cluster consists of gauges and lamps as shown below, to warn the operator in case of abnormal machine operation or conditions for the appropriate operation and inspection. · Gauges : Indicate operating status of the machine. · Warning lamp : Indicate abnormality of the machine (red). · Pilot lamp : Indicate operating status of the machine. The cluster installed on this machine does not entirely guarantee the condition of the machine. The cluster installed on this machine does not entirely guarantee the condition of the machine. Daily inspection should be performed according to chapter 6, Maintenance.

Daily inspection should be performed according to chapter 6, Maintenance. When the cluster provides a warning, immediately check the problem and perform the required When the cluster provides a warning, immediately check the problem and perform the required action. action. Menu button 35Z9A3CD03 4-3 essure warning lamp Battery charging pilot lamp Engine preheat warning lamp Overload warnin ant temp warning lamp Fuel low level w ant temp gauge Fuel leve d pilot lamp Up/Left button Enter/Bu Down/Right button OLED display Battery charging Engine preheat Overload warnin Fuel low level w Fuel leve

Стр. 4