Komatsu — HANDLING OIL, FUEL, COOLANT, AND PERFORMING OIL CLINIC

. MAINTENANCE OUTLINE OF SERVICE 4 - 5 FUEL To prevent the moisture in the air from condensing and forming water insid e the fuel tank, always fill the fuel tank after completing the day 's work. sion instrument, and if fuel containing water or dirt is used, it cannot work properly. t to let impurities get in when storing or adding fuel. cified for the temperature in the Operation and Maintenance Manual. The fuel pump is a preci sion instrument, and if fuel containing water or dir t is used, it cannot work properly.

Be extremely careful no t to let impurities get in when storing or adding fue Always use the fuel spe cified for the temperature in the Operation and Ma If the fuel is used at te °C (5°F), the fuel will If the fuel is used at t result in problems su If the fuel is used at te mperatures lower than the specified temperature ( particularly at temperatures below -15 solidify. If the fuel is used at t emperatures higher than the specified temperatur e, the viscosity will drop, and this may ch as a drop in output. Before starting the engin e, or when 10 minutes have passed after adding fu el, drain the sediment and water f rom the fuel tank.

If the engine runs out of fuel, or if the filters have been replaced, it is nece ssary to bleed the air from the circuit. If there is any foreign m aterial in the fuel tank, wash the tank and fuel sys tem. NOTICE uel. Always use diesel oil for the f To ensure good fuel consump tion characteristics and exhaust gas characteristics, the engine mounted on this machine use s an electronically controlled high- pressure fuel injection device. This device requires hig h precision parts and lubrication, so i f low viscosity fuel with low lubrica ting ability is used, the durability may drop markedly.

COOLANT AND WATER FOR DILUTION ortant function of preventing corrosion as well as preventing freezing. freezing is not an issue, the use of antifreeze coolant is essential. supplied with Komatsu Supercoolant (AF-NAC). Komatsu Supercoolant (AF-NAC) has The coolant has the imp ortant function of preventing corrosion as well as Even in the areas where freezing is not an issue, the use of antifreeze co Komatsu machines are supplied with Komatsu Supercoolant (AF-NAC). K omatsu Supercoolant (AF-NAC) has excellent anticorrosion, antifreeze and cooling propertiesand can be used c ontinuously for 2 years or 4000 hours.

As a basic rule, we do not recommend the use of any coolant other than Komatsu genuine supercoolant nother coolant, it may cause serious problems, such as corrosion of the engine and ooling system. eze coolant, use distilled water or tap water (soft water). a river water or well water (hard water), contains large amounts of minerals (calcium, than Komatsu genuine supercoolant (AF-NAC). If you use a and aluminum parts of the c When diluting the antifre eze coolant, use distilled water or tap water (soft Natural water, such as a river water or well water (hard water), contains magnesium, etc.), and th is makes it easier for scale to form inside the engin e or radiator.

Once scale is deposited inside the engine or rad iator, it is extremely difficult to remove. It also c auses overheating due to poor heat exchange, so when you dilute the coolant, we recommend that you use w less than 100 PPM. When using antifreeze, always observe the precautions given in the Oper Antifreeze coolant is fla mmable, so be sure to keep it away from flame. The ratio of Supercoola nt (AF-NAC) to water differs according to the amb For details of the ratio w hen mixing, see "CLEAN INSIDE OF COOLING Even in areas where it i s not necessary to prevent freezing, use Superco olant (AF-NAC) at a mixing ratio of at d diluting water.

of at least 30% to prevent co rrosion of the cooling system. Supercoolant (AF-NAC) may be supplied in premix. In this case, never ad If the engine overheats, wait for the engine to cool before adding coolant. If the coolant level is low , it will cause overheating, and will also cause prob lems with corrosion due to air entering the coolant.