. MAINTENANCE OUTLINES OF SERVICE 4 - 5 FUEL To prevent the moisture in the air from condensing and forming water inside the fuel tan k, always fill the fuel tank after completing the day's work. ument, and if fuel containing water or dirt is used, it cannot work properly. purities get in when storing or adding fuel. the temperature in the Operation and Maintenance Manual. The fuel pump is a precision instr ument, and if fuel containing water or dirt is used, it c annot work properly. Be extremely careful not to let im purities get in when storing or adding fuel.
Always use the fuel specified for the temperature in the Operation and Maintenance M If the fuel is used at temperatur °C (5°F), the fuel will solidify. If the fuel is used at temperatu result in problems such as a d If the fuel is used at temperatur es lower than the specified temperature (particularly a t temperatures below -15 If the fuel is used at temperatu res higher than the specified temperature, the viscosi ty will drop, and this may rop in output. Before starting the engine, or whe n 10 minutes have passed after adding fuel, drain the sediment and water f rom the fuel tank.
If the engine runs out of fuel, or if the filters have been replaced, it is necessary to blee d the air from the circuit. NOTICE Always use diesel oil for the fuel. To ensure good fuel consumption chara cteristics and exhaust gas characteristics, the engine moun ted on this machine use s an electronically controlled high-pressure f uel injection device. This device requires high precision pa rts and lubrication, so i f low viscosity fuel with low lubricating ability is used, the durability may drop markedly. COOLANT AND WATER FOR D ILUTION ction of preventing corrosion as well as preventing freezing. is not an issue, the use of antifreeze coolant is essential.
with Komatsu Supercoolant (AF-NAC). Komatsu Supercoolant (AF-NAC) has The coolant has the important fun ction of preventing corrosion as well as preventing fr Even in the areas where freezing is not an issue, the use of antifreeze coolant is esse Komatsu machines are supplied with Komatsu Supercoolant (AF-NAC). Komatsu Sup ercoolant (AF-NAC) has excellent anticorrosion, antifreeze and cooling propertiesand can be used continuously for 2 years or 4000 hours. As a basic rule, we do not reco mmend the use of any coolant other than Komatsu genuine supercoolant olant, it may cause serious problems, such as corrosion of the engine and tem.
ant (AF-NAC), there is no need to use a corrosion resistor. For details, see YSTEM (PAGE 4-21)". ant, use distilled water or tap water (soft water). ater or well water (hard water), contains large amounts of minerals (calcium, u genuine supercoolant (AF-NAC). If you use another co and aluminum parts of the cooling sys When using Komatsu Supercool "CLEAN INSIDE OF COOLING S When diluting the antifreeze cool Natural water, such as a river w ater or well water (hard water), contains large amou magnesium, etc.), and this makes it easier for scale to form inside the engine or radiator . Once scale is deposited inside the engine or radiator, it i s extremely difficult to remove.
It also causes overh eating due to poor heat exchange, so when you dilute the coolant, we recommend that you use water with an overall hardness of less serve the precautions given in the Operation and Maintenance Manual. o be sure to keep it away from flame. C) to water differs according to the ambient temperature. g, see "CLEAN INSIDE OF COOLING SYSTEM (PAGE 4-21)". overall hardness of less than 100 PPM. When using antifreeze, always ob serve the precautions given in the Operation and M Antifreeze coolant is flammable, s o be sure to keep it away from flame.
The ratio of Supercoolant (AF-NA C) to water differs according to the ambient tempera For details of the ratio when mixin g, see "CLEAN INSIDE OF COOLING SYSTEM (P Even in areas where it is not nec essary to prevent freezing, use Supercoolant (AF-NA of at least 30% to prevent corrosion of Supercoolant (AF-NAC) may be s upplied in premix. In this case, never add diluting wa If the engine overheats, wait for t he engine to cool before adding coolant. If the coolant level is low, it will cau se overheating, and will also cause problems with cor rosion due to air entering the coolant.