BAIC — BAIC Comanche Service Manual: Comprehensive Guide for PA-24 Series Aircraft

PIPER COMANCHE SERVICE MANUAL 2. Slide the baml lIut (47) iDto the forward smat anD IDd i.QIm tile an:achiDc bolt (49) with wa.sber throurb the fittiDI iDto the ann. 3. Tip,tcn bolt IDd check support fiuiDI fat ftccdom of rotatiOD. 4. Secure the aft support fittiDI (11) to the resr spar web with aa:achiDI bola. wuhcrs aDd nUll. S. POIitiOD maiD 1aDdiaI par IInIt .-mbly ill the wbed wU IIICi macb the &oDt Illpport fittiDI to the main spal'web witb atw:billt bola lDel wllben. 6. Usmc the &CCeII bole bebiDd tile rat spat. u.n the buJIFe tube (10) with wilber (44) (0.125. PIN 14843-20) WouP the rat ..

pport fittiDI lad iDto the leU Rnlt ann UIiDI eDouP sbim wuhen (12) bet'Wftll the rear IUpport firtiDlud the IInlt mil to dimjnjllb CDd play of the saut bousiDl. (Shim wuben are available in sizes O.OU. PIN 19513-10; 0.062. PIN 14843-93 i aDd 0.125. PIN 14843-20.) 7. Position the side brace support bracket (2%) OD the maiD tpU' web lDel secure with bolts aDd wMbers. c. ASlCmble the upper aDd lower dralliDks (24 lad 27) with piwt bOlt (26). d. Adju.a the lower dzat link to a cfimcDW'Il of 6.125 inches from caller of the middle pivot bolt to center of the rod end beariD.I. (Refet to Fipre ~10.) e. 1asta11 the 1aDcIiDt leU' door mnctiOD anD OD the Rnlt bouiDl aad scauc with bolt. wuben and nut.

f. Ata.eh the upper drq link to the .pport bracket witIl clevis bolt. wilber. Dut Uld cotter pin and the lower liDk to the stnlt b0usiDB wim bolt, wuben lot cacb side of be:ariIII aDdlIut. I. Check for elann" betwccn qlillk middle pivot bolt bad (26) and the main pit capstrip.and biDctinI of the lower dntJ liDk md ba.riq by m:ractiDt aDd «men di ", the par by bmd. If danDer is less than 0.062 of ID inch bctwca pivot bolt bad UId 1pU' capta'ip. IdditioAal shims (17) must be I.deled betwccn the stnIt arm and front suPPOrt brackcc. h. InStIll sruds (14) iD rear strUt arm aDd S1fety with miAilDum 0.041 (Spec. MS20995C41) wire 0]). i.

1llSUl1 bam:.l nut (46) ill rear strUt ann IDd iDIcrt bolt (9) with wMber duoup buape tube aDd tighten. NOTE It is sugencd that new UIIist sprine (19) be iDItIIIed if new bUDpc cords (5) are instaUed. to iDsate proper opeution of the system. j. Check Far strUt arm support beariap for fn:edom of rautioD by rctnetiDt md ext.ndm, the FU by hlLftd. k. Install utaehm, bolt aDd bwlpe cord in toller bndtct (7). 1. Install roller (6) iD bndc.u ILftd secure with pia, wubc:t aDd comr pill. m. Install inboard pulley (4) aDd buDpe cord utCIIlbly on buDpc tool (PIN 752 998). n. Seeure the outboard buDp cord bracket to ia fiaillc lit of the re. spat. o.

P1a.cc the maiD FU' in the up pGlition md secure the inboard bUll" pulley to the bunp um (10) with washers aDdbolt. LANDING GEAR AND BRAKE SYSTEM REVISED: 1013177 IJI