BAIC — BAIC Comanche Service Manual: Comprehensive Guide for PA-24 Series Aircraft

PIPER COMANCHE SERVICE MANUAL c. Actach the rmse:tioD SPrinl (22 or 23) to the craalllLilliClD IIld adiu. the coaer pin bftWCICD the sprinl aDd floorboard co maiIltaiD coup tcnsioa on the sprm, to bold the 1hnsmj.IioQ away from the mncrion torque tubc durinl cJIIG'I'l'Dcy par ateasioa. d. Lllbricare me torque anD mroupa bolt (13) aDd book the tn"""issjoD tv.be (19) 0ftT me bah. e. Place the ancqascy rdeuc baDdle (18) in the dowa aad locked poIitioQ.lock.iaI the tnD .. jaiOD Nbc uound the throup bolt. f. CODDee:t the decaica1 leads aDd tUde the prouccite c:owriaI OҐa' the termiDalI aDd tic at both ends. I. Check for properopention uad adjust. (Refer to panpoapb ~'4.) 6-46. Ranoval Of No.

Ge.r P1IIb~ CoD1I'01 Rod. (Refer to Fipre 6-14.) a. Place the airplane aD jada. (Refer to JackiDI. Secr:ion 11.) b. Remove carpet aftI.ChiDI screws aDd roU it buk off the frODt CCIlter accaI panel. c. Remove froDt CCDtG' acCCII panel by removiDl aaachinI SCftWS. On airplanes with Serial Nos. 24-4783. 140-4804 and up. remove the rcmction mD-.oD ac~ door locued benn:cD the cwo front scatS. d. DiscoDDCCt the crusmission by pu1liq up aD the rei_ leva'. e. Rem.ct the landinc aar IlDtil it banp in the Dean poIition. by .... the ClDCfPDCY au_on lever. f. Disconnect the push-pull rod (11) from the UDdenide of the left IOrque arm (9) by ranoviaa the cotter pin. wuber and pin. ,.

Disconnect the forward CDd of the rod at the left dni Uak located in the DOIC ~ wbeel weI1 by removing nuc. washer aDd bolt. Rctn.ct the FU moucb to allow removal of the arw:binl bolt throup provided hole ill the Dose section dwlncl. h. Remove the rod by rcmoviDJ CIId bariDt aDd pulliDl it tbtoap ... aDd DOle ~ wbeel well. 6.... 7. Removal Of MaiD Landi'nI Gar PuIM'uI CoBuol CIbJa. (Rda'to Fipft 6-14.) a, Place the airplane on jacks. (Refer to JackiDI. Section II.) b. Remove carpet aaachq screws and roU c:.upct back off the front cauer access panel. c. On airplanes with Serial Nos. 24-4783. 1 ..... 04 &adup. tanCWC the recractiOft mnsmission acccsa door located between the two front scats.

d. Remove the rear scacs and carpet attaehiDI screws. e. Roll the cu:pet back aDd remove floor panel jut 1ft of the mraction tnmIIlisllon. f. Disconnect thc mnani_ion by pulJiq up on the re1cue Incr. I· Retract the landin, ,eat until it banp in cbc Della potiIion. by usiDI the emeqcncy extension lever. h. Disconnect the mraction cables (7 aDd 8) from the torque arms (9 aDd 10) by removinc attac:hiDc cotter pins. wuhen aDd pins. i. Remove castle ftUts (3 &ad4) from cables It the bulkhad aft of the m:ractiOft tra.nIIIlisIion. J. Remove damps scc:uriq cables to bottom of the fuIclate. k.

Enter throUJh the wbed well and disconnect cable ends from upper maiD gear drag links by removing attaching nut. _uhen aDd bola. LANDING GEAR AND BRAKE SYSTEM REVISED: 6/25na IJ13