PIPER COMANCHE SERVICE MANUAL 7B-54. OU Screens. The oil SCreclll ue me preslUft screca, loeucd in a dome shaped hOllSiDg, above 1ftd between the mqnuos and the suction screen locaeed in the afe section of the sump. Tbese screens should be clCU'led ae eacb oil cbanp to remove any aCCWllulation of sludle and to examine for metal fJ.1.inp or chips. If mew pattides ue fOWld in the oil ICZftIll. the eapte should be examined for ineernal ciamac c. a. To remove the prasure screm, remove oil mnpcn.mn elcct::ricallad or the tempcn.aue bulb and the cap screws seCllriDl the housiDl. Note dle locadon of the screws u che round fillister hca.cl screw. if insulled.
mu.sc be mumed co upper ri,ht comer of the housiDt. If the flllilur bad ICtew is not rewulled in the same hole from which it was remowcl, ie is possible to cnck the moun=- flante of the vacuum pump. b. With the housinl aDd SCIft1l remowed. c1eul andinlpCu both irea, chcckthe matinI surface of the housinr and accasory cue for pee partida. c. InKft me screw inca the bousinllO thae the screw fia flush with the boutin, base. Usinr a new gasket. secure the houlinl to ia mounc:m, pad and torque cap screws to 7S inch poullds. d. The suction screen is mnoved from the sump by removm, the hex had plu, at the lower aft part of the sump. Clean and inspect the screen and psket.
rcplac:c tbe ,uku if over compressed or damaged. Insert the scrccn fully ineo the sump. insc&ll fukft and piUl' Suny the piUl' iB·55. ou Cooler. a. When conducUfti a routine enJine inspection, the oil coolcr(s).lincs and fitciftp should be checked for the following: 1. Oil cooler line attaehmcna sbould be txamined to be certain that all 1ft tithe and thete is no indicuion "f aouthrcadinl. (Sec C for oil line torque.) 2. Oillina muse have aclequarc c1anncc and be properly a1itncd. 3. Oil line supportS should be tithe, properly positioned and if wom should be replaced. 4. OUcooler should be checked for leakap or distorted cells. S. Cooling fUll should be clean and undamqed. b.
Durinl each engine overhaul, at indications of hiah oil rempCQcuI'CS or during a sao hour inspection, the oil cooler should be removed, cleaned and checked for damqed fUll and cells, When replacing the cooler, properly alip and do not over tighten the mounting bolts so thae the cooler would be dam.lfecl. While the oil cooler is removed. the oil lines should be disconnected and flushed. c. If it is found that oil is leaking around the line compression nua. check that the nuts are tightened to 12' inch pound wee torque or the nue may be backed off, migbtened finger right. plus a 3/4 rum, Do not over torque. d. Should oil continue to leak, ie may be necessary co replace the seal rings.
Also remove the compression nua &tid inspece the line ends in the uca of the SWilled females for collapsed wbine. This condition may be observed by lookiftl intO the tubing ends. Should the cubilll show indications that it is collapsed and new seal rinp and proper torque docs nee HOpleak.lle, the oil lines should be replaced. Also inspece the surfaces of the mating fietings for dam.lle. 18·56. Recommendations For Chanlinl Oil. (Ref. Lye. latest 5.1. No. 1014 .) a. If an additive oil is used in a new enline, or a newl)" overilawed engine, high oil consumption might possibly be experienced, The anti·friction additives of some of these oils will rcurd the break-ill of the piston ring!
and cylinder walls. This condition is cuily corrected by the use of straight mineral oil until normal oil consumption is obtained. thcn change to the additive type. POWER PLANT REVISED: 4/10/81 2F24