PIPER COMANCHE SERVICE MANUAL 7C-65. Oil SCNCIl. The suction saftn located in the left side of the en,iDe sump should be cleaned at each oil chantc to remove any accumulation of sludle and to Qamine for metal fittinls or chips. If meu.l pU'ticles are found i.D me screen. the eJIIiDe should be examiDed for iDtema1 damap. The suction screeD is removed from the sump by removiDi the hex had plu, at the lower left side of the sump. Clan and inspect the screen and psket and replace the ..... ce if OWl' compmled or damlpd. a.
The oil falter element should be removed &her each fifty hoWl of enliDe operation; this is accomplished by removiDJ the lockwiR from the bolt-hcad at tile end of the futer bousm,. looscninl the bolt. and remOYinl the fUm' IIIImbly from the adapcer. 7C-66. Oil Fiker I_au. b. Before diJc:ardiaI the filter dC1llCftt. rc1IIOve the oueer pcrforami paper cover. and usiDi a sb&rJl knife. CUt throqh the folds of the element at both ends, close to the metal caps. Then. c:arcfully unfold the pleated element and eumine the material trapped in the flltu for evide.ace of internal eftIU\e c:1a.m.qe such II chips or particles from bcariDp. In new or llcwly overhauled CDliDa.
some small particles of metallic wviDp milht be found; these arc pncrally of DO coascquencc &Del should not be confused with panicles produced by imp&C'tiDJ, abraion or pressure. Evidence of iDtcnl&1 eapae damafe found in the oil filtet juRifics further elWlWwion to determine the cause. c. After the element has been replaced. titbttn the atudlin, bolt within 15 to 18 foot pounds torque. Lockwire the bolt tbrouJb the loops on the side of the housint to the drilled head of the thermostatic valve. Be sure the lockwire is replaced at both the attaehiq bolt head and the thermostatic oil cooler by-pus valve. 7C-67. Turbo Oil Flow Check.
(Refer to Fipre 7C·17.) Should an indication of low turbo oil pressutc or flow eeeur, the foUowm, system checks may be accomplished. 1. InsWl a pressure .'ute with a raqe of 0 to 80 psi pressure in the pressure line to the turbocharJm alter the redue:tiOft check valve. a. To check oil pressure. 11K the foUowi .. procedure: Z. Start the enpne and warm up in the \lSU&l manner UfttU oil temperature is normal. 3. Idle eftlinc at 1000 RPM and observe pressure PUF. It should indicate a minimum of 15 psi. Run engine al ZOOO RP~ the pressure laUJC should rac:l a minimum of 30 psi and a nwumum of 5' psi. b. To cheek turbo oil flow, UK the foUowiDi procedlUe: 1.
Asccruin that the enrine oil sump is full as indicated on the dipstick. 2. Start the ensine and warm up in the usual lIWlner until oil temperature is normal. 3. StOP enpte and dixonnea: oil drain UDe. of the eurbochU'let to be checked. It the sump. ing. .... Plug Nmp connection where drain line wu disconnected. 5. Install test line. approximalely four feet IOIll. on discoDnea:ed turbo oil drain line. 6. Set twO clean one .&I1oncapacity containm below the eftliDe. 7. Allow the turbo oil drain test line to hane in one coftwner. 8. Start engine and idle at 1000 RPM. 9. When oil flows from the turbo oil drain line into the container.
qUickly direct the oil flow into the empty container and immediately start timiD, for one minute. 10. When one minute has passed. direct the oil flow into the scavencer container and StOP engine. 11. Measure the oil in the test container. It should be a minimum oi 0.4 quart. 12. Disconnect test line. remove plUJ irom dram line tee fitting and connect ~rbo 011 drain line to tee fitting. 13. Test oil flow of the other turbocharger unit by using the same procedure. POWER PlANT ISSUED: 8/1&n2 2 H21