PIPER COMANCHE SERVICE MANUAL not have tieu tabs. thoulh installatiOll is similar. Th. fastea.rs may be f.lt thrOlllh the rubber cell and by grippilll the caU skin with the fiDprs arouDd the f.teur area they My be installed in their bracket. To check if .ach futener i. secure reach bet .. en the cell alld wina exerting a sHiht pressure inward. e. Attach the fuelH ... to tbe molded !UP pie ЈittUlI aDd .. ewe. f. Make final inlpection prior to clociftl tbe fuel cell to make sur. the fuel cell is clear of foreiln matter such as lint. dust. oil or aay other ialtaUatioa _teriat. If the fuel cell is llot completely clean. wipe it with a lint-free cloth Sc.k8d in alcohol or Iatr ... ne. I.
PMition the sender UAit and/or fillet wt with its .. kat aDd iastaU the vent aed drain hc. Aliln the bolt hole. aDd inaert all bolts before tiChtelUftl. Torque tbe bolts accordini to require.-nts placarded on the cell. Special attention .bollld be liven to the boltand stld lenlths to avoid bottomina on the inside of the bUDd tapped hoi .. or do. nuts. Either of the .. conditions could produce an error which -.owd r.,lIlt in a lou of cOIIlpr .. sion of tbe sealiDl surface. h. Connect the sender unit wires and replace U. cover plate(s). la.ket(l) and screws. 8-10. Fuel Quantity h.tllutl", 5,.te 8-10a. Cfteclt Anti .....ju.tlII ... t Of Fuel Quantity I_leoti", 5,....... 1.
Completely drain the main Ind l\lXiiia" f_l cells that relate to the pUle that is to be checked. (Refer to Dramine Fuel Cell.. Section n.) 2. Level the airplane lonlitudinally .ad laterally. (Refer to LeveUCI. Section 11.) 3. Connect a 14-Yolt power supply to tbe airplue electrical .ystem Ind observe the fuel quantity .auee. It should read empty with the respective fuel .. lector lever at both the main and auxiliary ON positions. a. General Checks of System. 4. Add fuel to each cell in tbe amount of 3. is U.S. pUona to tbe luxiliary cell and 7.5 U.S• •allons to the _in cell. to brinl each cell to one~rt.r its full capacity, 5. Again move the .elector lever to both ON p .. itians aad .er.'!
~he 11111'1. At either position the quantity pointer should allan with allY part do the oae-quarter full laUie index. 6. Continue to add fuel in increments of 3.75 aDd 7.5 U.S. plloa to the auxiliary and main cells respectively for each quarter capacity at tbe cells. At each quarter increment. Witil full. check that tbe qualltity pointer alieftS with Iny part do the conesponding index. with the selector lever It either ON pOlition. i. Should the glUle aad the lllIlount of fdl in- the cell not correspond. the procedure in steps "btl thrOulb lid If lDay be nece.sary to isolate the trouble in the system. b. Serder Check. 1. Remove the fuel sender to be checked. (Refer to paraanph 8-1Ob.) 2.
Secure the sender in the appropriate position on the fabricated jil as shown in Figure 8-9, (The iii may be fabricated from dimensions liven in Filure 8-19.) 3. With the float arm .pilllt the bottOtrl stop. the float should be just touchina the base of the jig_ If the float arm is not touehinc the btlse of the jil or tM bottom stop. adjust the float by bending the arm at a poaition shown in Fiiure 8-9. 4. After the sencler has been adjusted. check for the proper amount of resistance by the followina pro~dure: FUEL SYSTEM 2 123