Komatsu — HANDLING OIL, FUEL, COOLANT, AND PERFORMING OIL CLINIC

. MAINTENANCE SECONDARY MATERIALS FOR OPERATION 4 - 12 FUEL After completing the day's operations, fill the fu el tank to force out any air containing moisture. This will prevent the moisture from condensing and mixing with t he fuel. fuel containing water or dirt is used, it cannot work properly. when storing or adding fuel. re in the Operation and Maintenance Manual. The fuel pump is a precision instrument, and if Be extremely careful not to let impurities get in Always use the fuel specified for the temperatu If the fuel is used at temperatures lower than °C (5°F), the fuel will solidify. If the fuel is used at temperatures higher tha result in problems such as a drop in output.

If the fuel is used at temperatures lower than the specified temperature (particularly at temperatures below -15 If the fuel is used at temperatures higher tha n the specified temperature, the viscosity will drop, and this may Before starting the engine, or when 10 minutes have passed after adding fuel, drain the sediment and water from the fuel tank. If the engine runs out of fuel, or if the filters hav e been replaced, it is necessary to bleed the air from the circuit. If there is any foreign material in the fuel tank, wash the tank and fuel system. Excess fuel in the tank may spill out due to ther mal expansion when the fuel temperature rises. Be careful not to fill with too much fuel.

NOTICE Use only diesel fuel. The engine mounted on this machine employs electron ic control and a high-pressure fuel injection device to obtain good fuel consumption and good exhaust gas characteristics. For this reason, it requires high precision for the parts and good lubrication. If kerosene or other fuel with low lubricating ability is us ed, there will be a big drop in durability. COOLANT AND WATER FOR DILUTION nting corrosion as well as preventing freezing. e, the use of antifreeze coolant is essential. Supercoolant (AF-NAC).

Komatsu Supercoolant (AF-NAC) has The coolant has the important function of preve Even in the areas where freezing is not an issu Komatsu machines are supplied with Komatsu excellent anticorrosion, antifreeze and cooling p ropertiesand can be used continuously for 2 years or 4000 hours. As a basic rule, we do not recommend the u se of any coolant other than Komatsu genuine supercoolant (AF-NAC). If you use another coolant, it may ca use serious problems such as corrosion of the engine and parts of the cooling system that use light metals such as aluminum. , there is no need to use a corrosion resistor. For details, see E 4-30)". ed water or tap water (soft water).

ter (hard water), contains large amounts of minerals (calcium, When using Komatsu Supercoolant (AF-NAC) "CLEAN INSIDE OF COOLING SYSTEM (PAG When diluting the antifreeze coolant, use distill Natural water, such as a river water or well wa magnesium, etc.), and this makes it easier for sc ale to form inside the engine or radiator. Once scale is deposited inside the engine or radiator, it is extremely d ifficult to remove. It also causes overheating due to poor heat exchange, so when you dilute the coolant, we r ecommend that you use water with an overall hardness of less than 100 PPM. cautions given in the Operation and Maintenance Manual. eep it away from flame.

ffers according to the ambient temperature. N INSIDE OF COOLING SYSTEM (PAGE 4-30)". When using antifreeze, always observe the pre Antifreeze coolant is flammable, so be sure to k The ratio of Supercoolant (AF-NAC) to water di For details of the ratio when mixing, see "CLEA Even in areas where it is not necessary to prev ent freezing, use Supercoolant (AF-NAC) at a mixing ratio of at stem. mix. In this case, never add diluting water. ool before adding coolant.

at least 30% to prevent corrosion of the cooling sy Supercoolant (AF-NAC) may be supplied in pre If the engine overheats, wait for the engine to c If the coolant level is low, it will cause overheatin g, and will also cause problems with corrosion due to air entering the coolant.