Komatsu D65EX-15E0, D65PX-15E0, D65WX-15E0 — STANDARD TIGHTERING TORQUE TABLE

SEN00056-01 00 Index and foreword 5. Table of tightening torques for hoses (taper seal type and face seal type) a Unless there are special instructions, tighten the hoses (taper seal type and face seal type) to the torque below. a Apply the following torque when the threads are coated (wet) with engine oil. 6. Table of tightening torques for 102, 107 and 114 engine series (Bolts and nuts) a Unless there are special instructions, tighten the metric bolts and nuts of the 102, 107 and 114 engine series to the torque below. 7.

Table of tightening torques for 102, 107 and 114 engine series (Eye joints) a Unless there are special instructions, tighten the metric eye joints of the 102, 107 and 114 engine series to the torque below. 26 D65EX, PX, WX-15E0 Nominal No. of hose Width across flats Tightening torque Nm {kgm} Taper seal Face seal Range Target Thread size (mm) Nominal No.

- Number of threads, type of thread Thread diame- ter (mm) (Ref- erence) 02 19 34 – 54 { 3.5 – 5.5} 44 { 4.5} – 9/16-18UN 14.3 34 – 63 { 3.5 – 6.5} 14 – – 03 22 54 – 93 { 5.5 – 9.5} 74 { 7.5} – 11/16-16UN 17.5 24 59 – 98 { 6.0 – 10.0} 78 { 8.0} 18 – – 04 27 84 – 132 { 8.5 – 13.5} 103 {10.5} 22 13/16-16UN 20.6 05 32 128 – 186 {13.0 – 19.0} 157 {16.0} 24 1-14UNS 25.4 06 36 177 – 245 {18.0 – 25.0} 216 {22.0} 30 1-3/16-12UN 30.2 (10) 41 177 – 245 {18.0 – 25.0} 216 {22.0} 33 – – (12) 46 197 – 294 {20.0 – 30.0} 245 {25.0} 36 – – (14) 55 246 – 343 {25.0 – 35.0} 294 {30.0} 42 – – Thread size Tightening torque Bolt BANJO bolt mm Nm kgm Nm kgm 6 8 10 12 14 10 ± 2 24 ± 4 43 ± 6 77 ± 12 – 1.02 ± 0.20 2.45 ± 0.41 4.38 ± 0.61 7.85 ± 1.22 – 8 ± 2 10 ± 2 12 ± 2 24 ± 4 36 ± 5 0.81 ± 0.20 1.02 ± 0.20 1.22 ± 0.20 2.45 ± 0.41 3.67 ± 0.51 Thread size Tightening torque mm Nm kgm 6 8 10 12 14 8 ± 2 10 ± 2 12 ± 2 24 ± 4 36 ± 5 0.81 ± 0.20 1.02 ± 0.20 1.22 ± 0.20 2.45 ± 0.41 3.67 ± 0.51