SEN00591-00 40 Troubleshooting Failure code [DB2RKR] Steering and transmission controller CAN communication: Defective communication 1 30 D65EX, PX, WX-15E0 Action code Failure code Symptom of failure Steering and transmission controller CAN communication: Defective communication (Steering and transmission controller system) CALL E03 DB2RKR Failure content • Steering and transmission controller cannot recognize engine controller with CAN communication circuit. Controller's action • Flashes warning lamp and turns on alarm buzzer. • Limits operation of engine and transmission. Symptoms that appears on machine • System may not operate normally.
• When machine is traveling, engine speed is limited up to medium (half) at a certain rate. • Once machine is stopped, engine speed is limited to medium (half). • Once machine is stopped, travel is limited to F1 and R1. General information • Duplication of failure code: turn ON the starting switch. Possible causes and the standard values when normal Cause Standard value when normal and remarks for troubleshooting 1 Disconnection in wiring harness (Disconnection or defective contact of connectors) aPrepare with starting switch OFF and diagnose with starting switch still OFF.
Wiring harness between S04 (female) (1) (2) – ST2 (female) (32), – CE02 (female) (46), – CA1 (female) (A), – CA2 (female) (A), – G01 (female) (8), and – SRV (male) (3) Resis- tance Max. 1 z Wiring harness between S04 (female) (3) (4) – ST2 (female) (22), – CE02 (female) (47), – CA1 (female) (B), – CA2 (female) (B), – G01 (female) (7), and – SRV (male) (10) Resis- tance Max. 1 z 2 Defective harness grounding (Contact with ground circuit) aPrepare with starting switch OFF and diagnose with starting switch still OFF.
Wiring harness between S04 (female) (1) (2) – ST2 (female) (32), – CE02 (female) (46), – CA1 (female) (A), – CA2 (female) (A), – G01 (female) (8), and – SRV (male) (3) with ground Resis- tance Min. 1 Mz Wiring harness between S04 (female) (3) (4) – ST2 (female) (22), – CE02 (female) (47), – CA1 (female) (B), – CA2 (female) (B), – G01 (female) (7), and – SRV (male) (10) with ground Resis- tance Min. 1 Mz 3 Hot short of wiring harness (Contact with 24 V circuit) aPrepare with starting switch OFF and diagnose with starting switch ON.
Wiring harness between S04 (female) (1) (2) – ST2 (female) (32), – CE02 (female) (46), – CA1 (female) (A), – CA2 (female) (A), – G01 (female) (8), and – SRV (male) (3) with ground Voltage Max. 1 V Wiring harness between S04 (female) (3) (4) – ST2 (female) (22), – CE02 (female) (47), – CA1 (female) (B), – CA2 (female) (B), – G01 (female) (7), and – SRV (male) (10) with ground Voltage Max. 1 V 4 Defective CAN terminal resistance aPrepare with starting switch OFF and diagnose with starting switch still OFF.
CA1 (male), CA2 (male) Resistance Between (A) – (B) 100 – 140 z 5 Defective monitor panel or defective steering and trans- mission controller If no problem is found in causes 1 – 4, it is suspected that monitor panel or steering and transmission controller is defective. (Troubleshooting cannot be carried out since it is internal defect.)