Fendt 900 Vario COM III — 20 Calibration fault codes

Check Chassis Range! 0000 - Overall system/tractor B - Faults 117 T006640 Version 2 09-10-2009 F55 Faulty speed signal from B014 - Sensor, collecting shaft F56 Faulty speed signal from B010 - Sensor, engine speed F54 Faulty speed signal from B015 - Sensor, bevel pinion F59 Travel range I button was actuated F61 Travel range II button was actuated F52 Engine speed below 1400 rpm F58 B017 - Sensor, clutch pedal faulty Calibration code 4007 ( A009 - Actuator unit) F60 Travel range I button faulty F53 Handbrake not applied F57 Clutch pedal depressed 919 .. 1001- 934 .. 1001- 922 .. 1001- 925 .. 1001- 928 .. 1001- 931 ..

1001- Fault code Cause B - Faults Fault code Cause F02 A009 - Actuator unit reporting a fault Frequent cause of fault: During previous fault-generated calibration exit, no "Key reset (ignition OFF/ON)" was carried out F03 A009 - Actuator unit fails to control the specified value exactly. Check that the transmission adjustment is smooth. F04 Transmission ratio adjustment not effected within 8 sec. Check that the transmission adjustment is smooth. F05 Step 1 = A009 - Actuator unit does not find neutral point 0 in forwards direction. Step 2 = A009 - Actuator unit does not find neutral point 0 in reverse direction. Check connection of A009 - Actuator unit to actuator shaft.

F06 See under error message F05 F07 Step 2: The neutral points of the transmission control system for forwards and reverse travel are too far apart, more than 8°. Check connection of A009 - Actuator unit to actuator shaft. F08 Step 3: Max. transmission ratio forward point not found. Specified value min. 155°, max. 187° Step 4: Max. transmission ratio reverse point not found. Specified value min. 136°, max. 165° Check connection of A009 - Actuator unit to actuator shaft. F09 Step 3: Forward actuator shaft adjustment greater than 155°. but transmission adjustment reacts less than 155° Step 4: Reverse actuator shaft adjustment greater than 135°.

but transmission adjustment reacts below 135° Check connection of A009 - Actuator unit to actuator shaft. F10 Transmission ratio characteristic not logical, e.g. shifted forward and reverse detected. Repeat calibration. See also error message F 2. Check rotational direction signal from B014 - Sensor, collecting shaft F11/12 Step 7: check Step 1 to Step 6 values. ML transmission ratio not OK. Repeat calibration. See also error message F 2. Then check hydrostatic power branch, e.g. via emergency operation. F13 1. EOL programmed incorrectly (prior to Step 1) 2. Values stored in the A050 - ECU, basic control unit are illogical Remedy: 1. Reprogram EOL. 2. See 1.

Replace A050 - ECU, basic control unit if necessary F14 See F 11/F 12 F15 Maximum forward and/or reverse transmission ratio not achieved. Remedy: Repeat calibration (see also F2). Then check hydraulic power distribution system if necessary, e.g. via emergency mode.

F50 User interrupted with "ESC" F51 Speed above 0,1 km/h F52 Engine speed below 1400 rpm F53 Handbrake not applied F54 Faulty speed signal from B015 - Sensor, bevel pinion F55 Faulty speed signal from B014 - Sensor, collecting shaft F56 Faulty speed signal from B010 - Sensor, engine speed F57 Clutch pedal depressed F58 B017 - Sensor, clutch pedal faulty F59 Travel range I button was actuated F60 Travel range I button faulty F61 Travel range II button was actuated