Fendt 900 Vario COM III — 4 A051 ECU, engine control unit (EDC 7)

2000 - Overall system/engine A - General Functions of the A051-ECU, engine control unit (EDC 7) The A051 - ECU, engine control unit (EDC 7). manages and controls the engine. The A051 - ECU, engine control unit (EDC 7). has the following management functions: All speed control The A051 - ECU, engine control unit (EDC 7). keeps the engine under constant load at the speed set by the foot throttle, hand throttle and memory key (target value), as long as the engine is capable of providing the necessary power.

Restriction of the maximum engine speed ("engine cut-off speed") Rail pressure restriction The Y091 - Dispensing unit (fuel) dispenses the exact fuel quantity to the rail that will be discharged by the injectors (Y095 to Y101). Control is exercised by the B086 - Rail pressure sensor, which reports the actual pressure to the A051 - ECU, engine control unit (EDC 7).. Cylinder switch-off If the A051 - ECU, engine control unit (EDC 7). detects a short circuit at an injector (Y095 to Y101) (short circuit low-high), this injector is no longer activated (shut down).

Monitoring and signal output functions Coolant temperature and charge-air temperature --> for fault displays and/or reductions in power see chapter 0000 Reg. B - Fault code table 15 T002538 Version 2 05-10-2009 Multiple injection With a view to a reduction in exhaust gas and noise emissions, the injectors (Y095 to Y101) are activated by the A051 - ECU, engine control unit (EDC 7). up to 3 times per working cycle. N OTE : If the rotational speed signals (camshaft / crankshaft) are not present after 5 sec, the start process is aborted Charge pressure-dependent engine management ("LDA function") If the charge-air temperature increases, the injection quantity will be restricted.

If the charge-air pressure drops, the in- jection quantity will be restricted. Preventing smoke formation N OTE : The A051 - ECU, engine control unit (EDC 7). contains an atmospheric pressure sensor. Boost pressure (over pressure) = absolute pressure (B092 sensor) - atmospheric pressure (A051 ECU). Actuation of the cold start system The R002 heater flange is activated by the A051 - ECU, engine control unit (EDC 7).. The indicator lamp for the R002 - Heater flange is located in the A007 - Instrument panel.

Activation of the exhaust gas recirculation (AGR) Depending on the operating conditions of the engine, a certain quantity of exhaust gases are fed back into the engine Fault log in the A051 - ECU, engine control unit (EDC 7). The A051 - ECU, engine control unit (EDC 7). forwards the EMR fault data to the A007 - Instrument panel, where the error messages are output on a display.

(FENDT fault code) Actuation of the injectors Energising the injector causes fuel to be injected; the duration determines the quantity that is injected The injectors inject fuel up to 3 times per working cycle Actuation of the engine brake The Y006 - Solenoid valve, engine brake is actuated by the A051 - ECU, engine control unit (EDC 7).. Fault diagnosis using the SERDIA service diagnostics program Reads all the sensors and the A051 - ECU, engine control unit (EDC 7). ("program:

Measured values") Temperature-dependent start control ("excess fuel at starting") Improved starting characteristics, engine protection at cold start without smoke plumes Altitude correction Avoidance of smoke plumes at low air density Engine protection at low air density. At high altitudes (Andes, Himalayas, etc.) the maximum engine power is restricted Torque restriction Restriction of the maximum torque (maximum injection quantity) Engine start If all input signals are present the start procedure is initiated. 919 .. 0101-1000 925 .. 1001- 934 .. 0101-1000 919 .. 1001- 928 .. 0101-1000 934 .. 1001- 922 .. 0101-1000 928 .. 1001- 922 .. 1001- 931 .. 0101-1000 925 .. 0101-1000 931 ..

1001- Emergency mode/Engine shutoff if necessary see chapter 0000 Reg. B - Fault code table see chapter 2000 Reg. A - Emergency mode Engine stop The injectors cease to be activated. A - General