2000 - Overall system/engine A - General I001150 Fig. 58. ARNING : If the A051 ECU, engine control unit is programmed with engine software that does not match the chassis number, any claims under warranty will be invalid. The person carrying out the programming is responsible for correctly carrying out the procedure and may be held liable if it is carried out incorrectly. The chassis number and engine number of the tractor are stored in the A051 ECU, engine control unit, as is the Serdia adapter serial number. If engine software that does not match the chassis number of the tractor is programmed, the tractor's im- mobiliser is activated. (i.e.
the A051 ECU, engine control unit does not release an injection volume). If an A051 ECU, engine control unit that does not match the tractor's chassis number is installed, the trac- tor's immobiliser is activated (i.e. the A051 ECU, engine control unit does not release an injection volume). If a new A051 ECU, engine control unit is installed, it must be programmed with the engine software that matches the tractor. The A051 ECU, engine control unit must then be taught to recognise the immobiliser. Only new components that have not yet been activated can be taught in. (See also:
Chapter 9015 Reg.F – Teaching in B083 immobiliser control unit and/or A051 ECU, engine con- trol unit.) The following conditions must be met in order to be able to replace the engine software or load it for the first time in an A051 ECU, engine control unit: 45 T000949 Version 2 31-10-2008 The programming procedure for the Deutz diagnosis program is protected by a password. This password varies according to the Serdia adapter Read off the serial number of the Serdia adapter Example: SN:131467 Report the Serdia adapter serial number to FENDT Cus- tomer Service: Telephone: +49 8342 / 77 - 123 Fax :
+49 8342 / 77 - 222 Fendt Customer Service will send you the valid password for the Serdia adapter Downloading SERDIA software from AGCONET: Customer service - FENDT - Customer service - Down- loads The engine software must be available. - Request the engine software from FENDT Customer service (Tel.: +49 (0) 8342 / 77 - 123) - The engine software will be sent to you in a "zipped" compressed file. - "Unzip" the file and save it to a folder Suggestion: Select the tractor's chassis number as the name of the folder. - Save the folder in: C:\Program Files\Deutz\Data Load the engine software onto the A051 ECU, engine control unit Programming process:
Please refer to the detailed description 20 A051 ECU, engine control unit (installing engine software) Note at the bulkhead, between engine and cab The settings (engine power, engine cut-off speed, governor behaviour, engine configuration etc.) have been saved in the engine software (engine data re- The engine software is installed on the A051 ECU, engine The most recent Deutz diagnostics program (SERDIA) must have been installed on the diagnostic computer (laptop) 919 .. 0101-1000 925 .. 1001- 934 .. 0101-1000 919 .. 1001- 928 .. 0101-1000 934 .. 1001- 922 .. 0101-1000 928 .. 1001- 922 .. 1001- 931 .. 0101-1000 925 .. 0101-1000 931 .. 1001- A051 = ECU, EDC engine control unit Open bonnet.
A - General Condition Note The programming procedure for the Deutz diagnosis program is protected by a password. This password varies according to the Serdia adapter Read off the serial number of the Serdia adapter Example: SN:131467 Report the Serdia adapter serial number to FENDT Cus- tomer Service: Telephone: +49 8342 / 77 - 123 Fax: +49 8342 / 77 - 222 Fendt Customer Service will send you the valid password for the Serdia adapter The most recent Deutz diagnostics program (SERDIA) must have been installed on the diagnostic computer (laptop) Downloading SERDIA software from AGCONET: Customer service - FENDT - Customer service - Down- loads The engine software must be available.
- Request the engine software from FENDT Customer service (Tel.: +49 (0) 8342 / 77 - 123) - The engine software will be sent to you in a "zipped" compressed file. - "Unzip" the file and save it to a folder Suggestion: Select the tractor's chassis number as the name of the folder. - Save the folder in: C:\Program Files\Deutz\Data Load the engine software onto the A051 ECU, engine control unit Programming process: Please refer to the detailed description