John Deere 326D, 328D, 332D — Control Panel Functions

Operation—Operator’s Station Control Panel Functions 1—Blower Speed Dial—If Equipped: Turn dial clockwise to increase blower speed. Blower has four speed settings plus an OFF position. 9—Quik-Tatch™Switch—If Equipped: Press and hold upper half of switch until lock pins are engaged. Press and hold lower half of switch until lock pins are retracted. 2—Cab Temperature Control Dial—If Equipped: Turn dial clockwise towards red zone for warmer air. Turn dial counterclockwise towards blue zone for cooler air. NOTE: The switch will automatically return to center position when released. The mounting plates will stop at the position they are in at the time the switch is released.

3—Engine Speed Control Dial: Turn dial clockwise towards the rabbit to increase engine speed. Turn dial counterclockwise towards the turtle to decrease engine speed. 10—Auxiliary Hydraulic Override Switch: Allows auxiliary hydraulics to operate after operator exits machine. This switch has two positions: Push upper half of switch to momentary position to activate bypass mode. Switch will return to lower position when released. NOTE: The engine control unit (ECU) will default engine speed to slow idle on engine startup regardless of engine speed control dial position.

Move engine speed control dial to slow idle position and then increase the setting to the desired speed to get the engine speed to increase. 11—Creep Mode Switch—If Equipped: If machine is equipped with an EH performance package, push upper half of switch to activate creep mode. Creep mode limits travel speed while maintaining engine speed. Engagement and monitor unit (EMU) displays prompts for selecting desired percentage. 4—Auxiliary Fourth Function Switch—If Equipped: Electric control of an auxiliary function. 5—Park Brake Switch: This switch has three positions: Push upper half of switch to engage park brake. This position also hydraulically locks the boom and bucket.

Push to middle position to hydraulically enable boom and bucket while park brake is engaged. 12—Reversing Fan Switch—If Equipped: Used to reverse the direction of fan rotation for purging debris from the radiator. This switch has three positions: Off—Disables reversing fan function. Auto (middle position)—Reverses fan every 20 minutes for 43 seconds. This position is used to prevent machine from overheating caused by accumulated debris against cooling package. Hydraulic oil temperature must be above 12°C (54°F). Manual—Press and hold switch in this position to manually activate reversing fan for 10 seconds. The switch can be used at any rpm.

Hydraulic oil temperature must be above 12°C (54°F). Switch is programmed to wait 60 seconds before allowing fan to reverse cycle again. NOTE: Operator must be in seat with seat belt fastened, with interlocking seat bar lowered, and engine must be running to disengage park brake. Push lower half of switch to momentary position and release to middle position to disengage park brake. 6—Key Switch: This switch has three positions: Position where ignition key can be inserted or removed is the OFF position. No circuits are active in this position. Turn key clockwise from the OFF position. This is the RUN position for the engine. Turn key clockwise from the RUN position.

This is the START position for the engine. After starting engine, release key. Key will return to RUN position. 13—Pattern Select Switch—If Equipped: If machine is equipped with an EH performance package, this switch allows for quick change of joystick functions between ISO or H control patterns. Push upper half of switch for H control pattern. Push lower half of switch for ISO control pattern. 7—Work Lights Switch: This switch has three positions: Push upper half of switch to turn on front work lights, red tail lights, and rear work light. Push to middle position to turn on front work lights and red tail lights. Push lower half of switch to turn lights off. 14—High Flow Switch—If Equipped:

Used for attachments that require a high hydraulic flow rate to operate. Push upper half of switch momentarily to turn ON and activate high flow option. Amber hydraulic high flow icon will appear on EMU. Push upper half of switch again to turn high flow option OFF. 8—Self Leveling Switch—If Equipped: Push upper half of switch to allow the attachment to remain in same relative position, as the boom is raised. Push lower half of switch to turn off this feature. 15—Dual Flasher Switch—If Equipped: Push upper half of switch to turn warning lights on. Push lower half of switch to turn warning lights off. NOTE: Self leveling is only operational during boom raise function.

16—Air Conditioner Switch—If Equipped: Push upper half of switch to turn on air conditioning. Push lower half of switch to turn off air conditioning. Continued on next page OUT4001,000046C -19-04FEB13-1/3 2-1-4 071713 PN=35