Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika final alignmenat are delivered spare keys for final machining. · Hang the turbine IP rotor on crane by means of the lifting beam ( Tp6079094 ). Wash the conservation from the rotorґs journals, level the hung rotor with max. deviation of 0,05mm/m and apply the oil for turning onto journals Novates (Novato). · Put the IP rotor into the bearings and into the empty bottom casing.
Set the slope of the front bearing stand and the bottom part of casing by the wedgeґs hammering and make the measurement by means of the level with accuracy of 0,02 mm/m, tighten the anchor bolts gradually up to min. torque in chapter „Foundation bolts“. · Measure with the inside micrometer the radial position of bottom casing and bearing stand against the rotor (the bore under the rotor, on the sides). Compare the readings with the values written in turbine Pasport book. If the difference is 0,05mm: continue. If the difference is > 0,05mm but the difference into account for the other measurements. If the difference is > 0,2mm: don’ continue, correct the partґs position.
· Take the rotor out · Assembly the splice bars of the cross beam without the spacer · Set the axial position of the bottom casing and front bearing stand: measure the gaps for spacers between the bottom casing and the end of cross beam, change the position with moving of the front bearing stand while the turbine casing is lifted a bit.
· Assembly spacers between cross beam ends and bottom casing (spacers are yet re-grinded on required dimension from pre-assembly), tighten screws of shim for connection bearing stands with bottom casing olny on seating of contact surface · The turbine casing prepare (bottom and cover) for the inner parts assembly, studs assembly and pilot pins into parting plane potřebnou tloušťku. Pro finбlnн nastavenн jsou dodбna nбhradnн pera pro dohotovenн. · Zavěste ST rotor na jeřбb pomocн zvedacн traverzy ( Tp6079094 ). Smyjte konzervaci z ložiskovэch čepů, vyrovnejte rotor do vodovбhy s max. chybou 0,05mm/m a naneste na čepy olej na protбčenн, např. olej Novates (Novato).
· Vložte ST rotors do ložisek (převэšenн ložisek již nastaveno) a prбzdnйho spodku tělesa. Proveďte přesnй nastavenн nбklonu ložiskovэch stojanů podbнjenнm kozlнků (měřenн vodovбhou o přesnosti 0,02 mm/m). Přitom utahujte průběžně zбkladovй šrouby na min. utahovacн moment)viz. kapitola „Zбkladovй šrouby“) · Proměřte mikrometrem radiбlnн pozici spodku tělesa a ložiskovэch stojanů vůči rotoru (vrtбnн tělesa – pod rotorem, na stranбch). Porovnejte hodnoty s hodnotami v pasportu turbiny. Pokud je rozdнl hodnot ≤0,05mm: pokračujte. Pokud je rozdнl hodnot >0,05mm, ale ≤0,2mm: pokračujte, berte v ъvahu odchylku pro dalšн měřenн. Pokud je rozdнl hodnot >0,2mm:
nepo kračujte, proveďte korekci poloh dнlů. · Vyjměte rotor · Montujte přнložky traverz bez mezikusů. · Ustavte axiбlnн polohu spodku tělesa a přednнho ložiskovйho stojanu: naměřenн spбry pro mezikus mezi spodkem tělesa a konci traverz, změna polohy - posouvбnнm přednнho ložiskovйho stojanu po nadlehčenн tělesa jeřбbem. · Montujte mezikusy mezi konce traverz a spodek tělesa (mezikusy jsou již přebroušeny na potřebnэ rozměr z kontrolnн montбže), šrouby přнložek pro spojenн ložiskovэch stojanů se spodkem tělesa dotahujte pouze na dosednutн kontaktnнch ploch. · Připravte vnějšн těleso (spodek i vнko) na montбž vnitřnнch dнlů, montujte zбvrtnй šrouby a vodнcн svнčky do dělнсн roviny.
Progress of work: · Bottom of IP casing is alignment on Stav pracн: · Spodek ST tělesa je ustaven na Date: 12.11.2013 Page 168 / 278 Prepared: O.Baroch Last Revision: Approved: P.Lešetickэ