Cummins — 4021531

Lubricating Oil Recommendations and Specifications QSB4.5 and QSB6.7 Page V-10 Section V - Maintenance Specifications Lubricating Oil Recommendations and Specifications General Information The fuel sulphur content should not exceed 0.5 mass percent sulphur. If the fuel sulphur content is greater than 0.5 mass percent sulphur, seek advice from your local Cummins® Distributor. For recommendations of fuel for Cummins® engines, refer to Fuel for Cummins® Engines, Bulletin 3379001. CAUTION CAUTION Extending the oil and filter change interval beyond the recommendations will decrease engine life due to factors such as corrosion, deposits and wear. Cummins Inc. does not recommend the use of A.C.E.A.

E4/MB 228.5 formulation oils, which do not attain one or more of the following lubricant qualifications: A.P.I. CH-4. CI-4, A.C.E.A. E5. E7, C.E.S. 20071, C.E.S. 20072, C.E.S. 20076, C.E.S. 20077, C.E.S. 20078. If A.C.E.A. E4/MB 228.5 formulation oils, which do not comply with the oil specifications listed above, are used in Cummins® automotive engines, problems such as wear to overhead, sliding tappets, camshaft and crankshaft bearings may be experienced. CAUTION The use of quality engine lubricating oils, combined with appropriate oil drain and filter change intervals, is a critical factor in maintaining engine performance and durability.

Extending the oil and filter change interval beyond the recommendations will decrease engine life due to factors such as corrosion, deposits and wear. NOTE: The responsibility is with the owner. If recommendations are ignored, warranty could be affected. NOTE: A.C.E.A. = Association des Constructeurs Europйen d'Automobiles, A.P.I. = American Petroleum Institute and C.E.S. = Cummins® Engineering Standard. Cummins Inc.

recommends the use of a high-quality SAE 15W-40 heavy-duty engine oil, such as Valvoline Premium Blue™, which meets or exceeds the American Petroleum Institute (API) performance classification CH-4/SJ or CI-4/ SK and the Association des Constructeurs Europйen d'Automobiles (A.C.E.A.) performance classification E5 or E7. A sulfated ash limit of 1.0 mass percent is suggested for optimum valve and piston deposit, and oil consumption control. The sulfated ash must not exceed 1.85 mass percent. Special “break-in” oils are not recommended for use in new or rebuilt Cummins® engines. Use the same lubricating oil that will be used in normal engine operations.

Use of "synthetic engine oils" (those made with API group 3 or group 4 base stocks) is permitted subject to the same performance and viscosity limitations of petroleum (mineral) based engine oils. The same oil change intervals must be applied to synthetic oils that are applied to petroleum (mineral) based engine oils. For further details and discussion of engine lubricating oils for Cummins® engines, refer to Cummins® Engine Oil Recommendations, Bulletin 3810340. Cummins® Engineering Standard Classifications (CES) American Petroleum Institute Classification (API) European Classification (ACEA) Comments API CD API CE ACEA E-1, ACEA E-2 OBSOLETE. DO NOT USE.

CES-20075 API CF-4/SG, API CG-4/SH ACEA E-3 Minimum acceptable oil classification for Midrange engines. (1) CES-20071, CES-20072, CES-20076, CES-20077 API CH-4/SJ ACEA E-5, E-7 Good oil classification for Midrange engines without EGR. CES-20078 API CI-4/SK Excellent oil for Midrange engines. 1. CG-4/SH and E-3 oils can be used in areas where none of the recommended oils are available, but the oil drain interval must be reduced by one half of the interval given in the maintenance schedule. See the oil drain interval information in Section 2.