Western Star — Western Star (EN)

Emissions and Fuel Efficiency Greenhouse Gas Emissions and Fuel Consumption Standards Engine lube oil must have a sulfated ash level less than 1.0 wt %; currently referred to as CJ-4 oil. IMPORTANT: Using non-specification fuels or oils can lead to shortened diesel particulate filter (DPF) cleaning or replacement intervals. For example, using CJ-4+ oil with 1.3% sulfated ash (30% more ash content) may result in the need for DPF cleaning or replacement 20 to 30% sooner than would normally be required. Vehicles and/or engines manufactured after Decem- ber 31, 2006 and domiciled in the U.S. or Canada are required to meet all EPA and NHTSA regulations effective as of the vehicle build date.

Engines manu- factured between January 1, 2007 and December 31, 2009 meet EPA07 requirements. Engines manufac- tured between January 1, 2010 and December 31, 2012 meet EPA10 requirements. IMPORTANT: See the engine manufacturer’s operation manual for complete details and op- eration of the ATS. Model year 2013 and later vehicles meet additional requirements as specified by NHTSA and EPA 2014 fuel efficiency and greenhouse gas emission stan- dards (GHG14). These vehicles are equipped with components that increase fuel efficiency and reduce GHG emissions.

Components may include, but are not limited to, low-rolling resistance tires; aerody- namic devices such as hood, cab/sleeper extenders, and fuel tank fairings; vehicle speed limiter; and idle shutdown timer. If replacement of any drag-reducing component is required, the replacement component must meet or exceed the drag reduction performance of the originally installed component in order to main- tain compliance with GHG14. EPA07 Engines Engines built between January 1, 2007 and Decem- ber 31, 2009 are required to meet EPA07 guidelines for reduced exhaust emissions of particulate matter and nitrogen oxides (NOx).

NOx is limited to just over 1 gram per brake horsepower hour (g/bhp-hr), and particulate matter cannot exceed 0.01 g/bhp-hr. The EPA07 ATS varies according to engine manufac- turer and vehicle configuration, but the exhaust muf- fler is replaced by an aftertreatment device (ATD). Inside the ATD, the exhaust first passes over the die- sel oxidation catalyst (DOC), then passes through the diesel particulate filter (DPF), which traps soot particles. The soot is burned to ash during a process called regeneration (regen). EPA-Regulated Emissions Aftertreatment Systems IMPORTANT: Depending on local jurisdictional guidelines, vehicles that are domiciled outside of the U.S.

and Canada may not have emissions aftertreatment systems (ATS) that are compliant with EPA regulations. EPA10 and Newer Engines The EPA mandates that all engines built after De- cember 31, 2009 must reduce the level of emissions exhausted by the engine to the following levels: NOTICE Nitrogen Oxides (NOx) 0.2 g/bhp-hr Follow these guidelines for engines that comply with EPA07 or newer regulations, or damage may occur to the aftertreatment device (ATD) and the warranty may be compromised.

Particulate Matter (PM) .01 g/bhp-hr To meet EPA guidelines, engines that are compliant with EPA10 and newer regulations use an ATS that has, in addition to a DOC/DPF device like that used in an EPA07 ATD, a Selective Catalytic Reduction (SCR) devide to reduce NOx downstream of the en- gine. After exhaust gases leave the DPF, a controlled quantity of diesel exhaust fluid (DEF) is injected into the exhaust stream. In the presence of heat, DEF is converted to ammonia gas, which reacts with NOx in the selective catalyst chamber to yield nitrogen and water vapor, which exit through the tailpipe. Use ultralow-sulfur diesel with 15 ppm sul- fur content or less.

Do not use fuel blended with used engine lube oil or kerosene. 11.1