ELECTRICAL SYSTEM 1. Removing electrical system ..........12-2 1.1 Removing starter.................................... 12-2 1.2 Inspection before removing alternator (A007TA0171B (12V-40A), A007TA8271A (24V-25A))..................... 12-3 1.2.1 Inspecting alternator operation.................12-3 1.2.2 Handling precaution .................................12-3 1.2.3 Inspecting regulated voltage ....................12-4 1.2.4 Inspecting output......................................12-4 1.3 Removing alternator............................... 12-5 1.4 Removing stop solenoid......................... 12-5 1.5 Removing glow plug...............................
12-6 2.4.14 Inspecting insulation of magnetic switch (between M terminal and B terminal)..... 12-17 2.5 Reassembling starter (M000T60481 (12V-1.2kW), M001T68381 (12V-1.7kW)).................. 12-18 2.5.1 Applying grease..................................... 12-18 2.5.2 Installing pinion...................................... 12-19 2.5.3 Installing gear shaft ............................... 12-19 2.5.4 Installing yoke and armature ................. 12-20 2.5.5 Installing brush holder and brush assembly ..................................... 12-20 2.5.6 Installing rear bracket ............................ 12-20 2.5.7 Installing magnetic switch......................
12-20 2.5.8 Inspecting pinion clearance................... 12-21 2.6 Inspection before disassembling starter (M002T66071 (24V-3.2kW)) ................ 12-22 2.6.1 Inspecting pinion clearance................... 12-22 2.6.3 No load test ........................................... 12-24 2.7 Disassembling and inspecting starter (M002T66071 (24V-3.2kW)) ................ 12-25 2.7.1 Preparation before disassembling......... 12-26 2.7.2 Removing magnetic switch.................... 12-26 2.7.3 Removing rear bracket .......................... 12-26 2.7.4 Removing brushes, brush holder, yoke and armature .........................................
12-27 2.7.5 Removing ball bearing........................... 12-27 2.7.6 Removing cover set............................... 12-27 2.7.7 Removing center bracket....................... 12-28 2.7.8 Removing reduction gear and spring set............................................... 12-28 2.7.9 Removing pinion set.............................. 12-28 2.7.10 Removing lever and pinion shaft ........... 12-28 2.8 Inspecting and repairing starter (M002T66071 (24V-3.2kW)) ................ 12-29 2.8.1 Inspecting brushes for wear .................. 12-29 2.8.2 Measuring brush spring load ................. 12-29 2.8.3 Inspecting brush holder for insulation....
12-29 2.8.4 Measuring commutator radial runout..... 12-30 2.8.5 Measuring commutator outside diameter12-30 2.8.6 Measuring undercut depth..................... 12-30 2.8.7 Checking armature coil.......................... 12-31 2.8.8 Inspecting continuity of yoke assembly . 12-32 2.8.9 Inspecting insulation between yoke body and brush............................................... 12-32 2.8.10 Inspecting center bracket ...................... 12-32 2.8.11 Inspecting overrunning clutch................ 12-33 2.8.12 Inspecting pinion.................................... 12-33 2.8.13 Inspecting front bracket ......................... 12-33 2.8.14 Inspecting gears of starter.....................
12-33 2. Disassembling, inspecting and reassembling electrical system .....12-7 2.1 Inspection before disassembling starter (M000T60481 (12V-1.2kW), M001T68381 (12V-1.7kW)) ................... 12-7 2.1.1 Inspecting pinion clearance......................12-7 2.1.3 No load test ..............................................12-9 2.2 Disassembling and inspecting starter (M000T60481 (12V-1.2kW), M001T68381 (12V-1.7kW)) ................. 12-10 2.3 Preparation before disassembling .......
12-11 2.3.1 Removing pinion set...............................12-11 2.3.2 Removing magnetic switch ....................12-11 2.3.3 Removing rear bracket...........................12-12 2.3.4 Removing brush holder and brush assembly ......................................12-12 2.3.5 Removing armature and yoke ................12-12 2.3.6 Removing overrunning clutch.................12-13 2.3.7 Removing gear shaft ..............................12-13 2.4 Inspecting and repairing starter (M000T60481 (12V-1.2kW), M001T68381 (12V-1.7kW)) .................
12-14 2.4.1 Inspecting brushes for wear ...................12-14 2.4.2 Measuring brush spring load..................12-14 2.4.3 Inspecting brush holder for insulation ....12-14 2.4.4 Measuring commutator radial runout .....12-15 2.4.5 Measuring commutator outside diameter12-15 2.4.6 Measuring undercut depth .....................12-15 2.4.7 Checking armature coil ..........................12-16 2.4.8 Inspecting rear bracket...........................12-16 2.4.9 Inspecting overrunning clutch ................12-17 2.4.10 Inspecting pinion ....................................12-17 2.4.11 Inspecting front bracket..........................12-17 2.4.12 Inspecting gears of starter......................12-17 2.4.13 Inspecting continuity of magnetic switch (between M terminal and case)..............12-17 12-1