Komatsu — HANDLING OIL, FUEL, COOLANT, AND PERFORMING OIL CLINIC

. MAINTENANCE OUTLINE OF SERVICE 4 - 6 FUEL To prevent the moisture in the air from conden sing and forming water inside the fuel tank, always fill the fuel tank after completing the day's work. fuel containing water or dirt is used, it cannot work properly. when storing or adding fuel. s given in the Operation and Maintenance Manual.

The fuel pump is a precision instrument, and if fuel containing water or dirt is used, it cannot work properly Be extremely careful not to let impurities get in Always use fuel that matches the temperature If the fuel is used in temperatures lower tha of lower than -15°C), the properties of the f If the fuel is used in temperatures higher tha this may result in a drop in output or other p If the fuel is used in temperatures lower tha n the specified temperature for use (particularly at temperatures uel will make it congeal. If the fuel is used in temperatures higher tha n the specified temperature for use, the viscosity will go down, and roblems.

Before starting the engine, or when 10 minutes have passed after adding fuel, drain the sediment and water from the fuel tank. If the engine runs out of fuel, or if the filters ha ve been replaced, it is necessary to bleed the air from the circuit. If there is any foreign material in the fuel tank, wash the tank and fuel system. NOTICE Use only diesel fuel. The engine mounted on this machine employs electro nic control and a high-pressure fuel injection device to obtain good fuel consumption and good exhaust gas characteristics. Fo r this reason, it requires high precision for the parts and good lubrication.

If kerosene or other fuel with low lubricating ability is u sed, there will be a big drop in durability. COOLANT AND WATER FOR DILUTION enting corrosion as well as preventing freezing. ue, the use of antifreeze coolant is essential. Supercoolant (AF-NAC). Komatsu Supercoolant (AF-NAC) has The coolant has the important function of prev Even in the areas where freezing is not an iss Komatsu machines are supplied with Komatsu Supercoolant (AF-NAC). Komatsu Supercoolant (AF-NAC) excellent anticorrosion, antifreeze and cooling propertiesand can be used continuously for 2 years or 4000 hours.

As a basic rule, we do not recommend the use of any coolant other than Komatsu genuine supercoolant (AF-NAC). If you use another coolant, it may c ause serious problems such as corrosion of the engine and parts of the cooling system that use light metals suc h as aluminum. ), there is no need to use a corrosion resistor. For details, see GE 4-27)". led water or tap water (soft water).

ater (hard water), contains large amounts of minerals (calcium, When using Komatsu Supercoolant (AF-NAC "CLEAN INSIDE OF COOLING SYSTEM (PA When diluting the antifreeze coolant, use distil Natural water, such as a river water or well w magnesium, etc.), and this makes it easier for s cale to form inside the engine or radiator. Once scale is deposited inside the engine or radiator, it is extremely difficult to remove. It also causes overheating due to poor heat exchange, so when you dilute the coolant, we recommend that you use water with an overall hardness of less than 100 PPM. ecautions given in the Operation and Maintenance Manual. keep it away from flame.

iffers according to the ambient temperature. AN INSIDE OF COOLING SYSTEM (PAGE 4-27)". When using antifreeze, always observe the pr Antifreeze coolant is flammable, so be sure to The ratio of Supercoolant (AF-NAC) to water d For details of the ratio when mixing, see "CLE Even in areas where it is not necessary to pre vent freezing, use Supercoolant (AF-NAC) at a mixing ratio of at ystem. emix. In this case, never add diluting water. cool before adding coolant.

of at least 30% to prevent corrosion of the cooling s Supercoolant (AF-NAC) may be supplied in pr If the engine overheats, wait for the engine to If the coolant level is low, it will cause overheati ng, and will also cause problems with corrosion due to air entering the coolant.