. MAINTENANCE TIGHTENING TORQUE SPECIFICATIONS TIGHTENING TORQUE SPECIFICATIONS TIGHTENING TORQUE LIST CAUTION Apply the following table for Hydraulic Hose. · m (kgf · m)] Permissible range 35 - 54 (3.5 - 5.5) 54 - 93 (5.5 - 9.5) 84 - 132 (8.5 - 13.5) 128 - 186 (13.0 - 19.0) 177 - 245 (18.0 - 25.0) 176 - 234 (18 - 24) The torques marked * indicate the tightening torques for the hoses at the top of the swivel joint. 4 - 13 If nuts, b olts, or oth er parts are not tightened to th e specified torque, i t wil l cause looseness or dam age to the tightened part s, and this will cause failu re of the m achine o r problems with operation.
Always p ay careful attention when tightening par Unless otherwise specified , tighten the metr ic nuts and bolts to t he torque shown in th e table below. If it is ne cessary t o replace any nut or bolt, always use a Komatsu genuine part of the sa me size as the part tha t was replaced.
Thread diameter of bolt (a)(mm) Width across flats (b)(mm) Tightening torque Target value Service limit N·m kgf·m lbft N·m kgf·m lbft 6 8 10 12 14 10 13 17 19 22 13.2 31 66 113 172 1.35 3.2 6.7 11.5 17.5 9.8 23.1 48.5 83.2 126.6 11.8-14.7 27-34 59-74 98-123 153-190 1.2-1.5 2.8-3.5 6.0-7.5 10.0-12.5 15.5-19.5 8.7-10.8 20.3-25.3 43.4-54.2 72.3-90.4 112.1-141 16 18 20 22 24 24 27 30 32 36 260 360 510 688 883 26.5 37 52.3 70.3 90 191.7 267.6 378.3 508.5 651 235-285 320-400 455-565 610-765 785-980 23.5-29.5 33.0-41.0 46.5-58.0 62.5-78.0 80.0-100.0 170.0-213.4 238.7-296.6 336.3-419.5 452.1-564.2 578.6-723.3 27 30 33 36 39 41 46 50 55 60 1295 1720 2210 2750 3280 132.5 175.0 225.0 280.0 335.0 958.4 1265.8 1627.4 2025.2 2423.1 1150-1440 1520-1910 1960-2450 2450-3040 2890-3630 118.0-147.0 155.0-195.0 200.0-250.0 250.0-310.0 295.0-370.0 853.5-1063.3 1121.1-1410.4 1446.6-1808.3 1808.3-2242.2 2133.7-2676.2 Thread diameter a (mm) Width across flat b(mm) Target value 9/16 -18UNF 19 44 (4.5) 11/16 -16UN 22 74 (7.5) 13/16 -16UN 27 103 (10.5) 1 -14UNS 32 157 (16.0) 1·3/16 -12UN 36 216 (22.0) *1-7/16-12UN -2B 41 215 (22)