Doosan Infracore D18NAP — Tightening Torque of General Bolts

6. About the engine Tightening Torque of General Bolts Please refer to the following tightening torque for the bolts which are not listed in Tightening Torque of Main Parts. 1. Tightening Torque of General Bolts Note) The standard torque values above are about 70% of the bolt elastic limit values. Note) A special screw should be tightened with 85% of the tightening torque of the standard value. For example, a MoS2-coated screw should be tightened with 60% of the tightening torque of the standard value. Note) The tensile force has been calculated by multiplying the tensile strength with the screw cross- sectional area.

6 - 5 Nominal Diameter × Pitch (mm) Strength Classification 3.6 4.6 4.8 5.6 5.8 6.6 6.8 6.9 8.8 10.9 12.9 (4A) (4D) (4S) (5D) (5S) (6D) (6S) (6G) (8G) (10K) (12K) Elastic Limit Value (kg/mm2) 20 24 32 30 40 36 46 54 64 90 106 Tightening Torque (kg•m) M5 0.15 0.16 0.25 0.22 0.31 0.28 0.43 0.48 0.5 0.75 0.9 M6 0.28 0.30 0.45 0.4 0.55 0.47 0.77 0.85 0.9 1.25 1.5 M7 0.43 0.46 0.7 0.63 0.83 0.78 1.2 1.3 1.4 1.95 2.35 M8 0.7 0.75 1.1 1 1.4 1.25 1.9 2.1 2.2 3.1 3.8 M8 X 1 0.73 0.8 1.2 1.1 1.5 1.34 2.1 2.3 2.4 3.35 4.1 M10 1.35 1.4 2.2 1.9 2.7 2.35 3.7 4.2 4.4 6.2 7.4 M10 X 1 1.5 1.6 2.5 2.1 3.1 2.8 4.3 4.9 5 7 8.4 M12 2.4 2.5 3.7 3.3 4.7 4.2 6.3 7.2 7.5 10.5 12.5 M12 X 1.5 2.55 2.7 4 3.5 5 4.6 6.8 7.7 8 11.2 13.4 M14 3.7 3.9 6 5.2 7.5 7 10 11.5 12 17 20 M14 X 1.5 4.1 4.3 6.6 5.7 8.3 7.5 11.1 12.5 13 18.5 22 M16 5.6 6 9 8 11.5 10.5 17.9 18.5 18 26 31 M16 X 1.5 6.2 6.5 9.7 8.6 12.5 11.3 17 19.5 20 28 33 M18 7.8 8.3 12.5 11 16 14.5 21 24.2 25 36 43 M18 X 1.5 9.1 9.5 14.5 12.5 18.5 16.7 24.5 27.5 28 41 49 M20 11.5 12 18 16 22 19 31.5 35 36 51 60 M20 X 1.5 12.8 13.5 20.5 18 25 22.5 35 39.5 41 58 68 M22 15.5 16 24.5 21 30 26 42 46 49 67 75 M22 X 1.5 17 18.5 28 24 34 29 47 52 56 75 85 M24 20.5 21.5 33 27 40 34 55 58 63 82 92 M24 X 1.5 23 25 37 31 45 38 61 67 74 93 103