DISASSEMBLY AND ASSEMBLY CONTROL VALVE ASSEMBLY OF CONTROL VALVE ASSEMBLY Before assembling coat the sliding surface with engine oil. 6. LS shuttle valve, LS select valve 1) Fit O-ring and install LS select valve (26). LS select valve: 127.5 ± 19.6 Nm (13 ± 2 kgm). 2) Fit O-rings and install LS shuttle valves (25a) and 25b). LS shuttle valve: 166.7 ± 19.6 Nm (17 ± 2.0 kgm). # Check valve (25a) and (25b) and be careful not to mistake them when install- ing. 1. Cooler bypass valve Assemble sleeve (54), piston (53), and spring (52) to cover (46), then fit O-ring to case (51) and install. 2.
Lift check valve Assemble sleeve (50), piston (49), and spring (48) to cover (46), then fit O-ring to case (47) and install. 7. Pressure compensation valve Check marks made on each pressure compensa- tion valve when disassembling, and install pres- sure compensation valves in correct position. 1) Before installing pressure compensation valves below, install check valves (17) and (24). 2) Fit O-ring, then install swing LEFT pres- sure compensation valve (23), travel FORWARD pressure compensation valve (22), pressure compensation valve (21), boom RAISE pressure compensa- tion valve (20), arm OUT pressure com- pensation valve (19), and bucket DUMP pressure compensation valve (18).
3) Fit O-ring, then install swing RIGHT pressure compensation valve (16), travel REVERSE pressure compensa- tion valve (15), pressure compensation valve (14), boom LOWER pressure compensation valve (13), arm IN pres- sure compensation valve (12), and bucket CURL pressure compensation valve (11). Pressure compensation valve: 225.5 ± 19.5 Nm (23 ± 2 kgm) 3. Cover, check valve, arm counterbalance valve 1) Fit O-rings and install covers (46) and (45). Mounting bolt of cover (46): 227.1 ± 32.3 Nm (28.3 ± 3.3 kgm). Mounting bolt of cover (45): 166.3 ± 10.3 Nm (17 ± 1 kgm) # Tighten the mounting bolts in the order shown in the diagram.
2) Assemble check valve (44) and spring (43), then fit O-ring to flange (42) and install. 3) Fit O-ring to arm counterbalance valve (41) and install. Mounting bolt: 31 ± 3.5 Nm (3.2 ± 0.4 kgm). # Tighten the mounting bolts in the order shown in the diagram. 4. Travel control valve, stabilizer control valve 1) Assemble spool assembly (37) to valve body. 2) Assemble retainer (40) and spring (39) to spool, then fit O-ring to case (38) and install. # Check springs (32) and (39), and be careful not to mistake them when install- ing. Mounting bolt: 11.3 ± 15 Nm (1.2 ± 0.2 kgm) 3) Assemble retainer (36) and spring (35) to spool, then fit O-ring to case (34) and install. Mounting bolt:
11.3 ± 1.5 Nm (1.2 ± 0.2 kgm). 8. Suction valves, safety-suction valves, unload valve 1) Fit O-rings and install suction valves (10) and (9). Suction valve: 147 ± 9.8 Nm (15 ± 1kgm). 2) Fit O-rings and install safety-suction valves (8), (7), (6), (5), and (4). Safety-suction valve: 147.1 ± 9.8 Nm (15 ± 1 kgm). 3) Fit O-ring and install unload valve (3). Unload valve: 166.7 ± 19.7 Nm (17 ± 2 kgm). 5. Bucket control valve, arm control valve, boom control valve, swing control valve 1) Assemble spool assembly (30) to valve body. 2) Assemble retainer (33) and spring (32) to spool, then fit O-ring to case (31) and install. # Check spring (32) when installing. Mounting bolt:
11.3 ± 1.5 Nm (1.2 ± 0.2 kgm). 3) Assemble retainer (29) and spring (28) to spool, then fit O-ring to case (27) and install. Mounting bolt: 11.3 ± 1.5 Nm (1.2 ± 0.2 kgm) 9. Main relief valve 1) Fit O-ring and install main relief valve (1). Main relief valve: 98.1 ± 9.8 Nm (10 ± 1 kgm). 30-83