Freightliner FLD Conventional — FLD Conventional

Heater and Air Conditioner HVAC General Information A FRESH/RECIRC push button ( Fig. 4.5 ) is standard equipment when there is no air conditioning. This control is an option when air conditioning is ordered. It allows the AC, VENT, and HEAT modes to be used with either fresh or recirculated air. When the mode control (upper lever) is at HEAT/DEF or DEF, the system draws in fresh air, regardless of the FRESH/ RECIRC push button setting. When the mode control is at MAX A/C, the system draws only recirculated air, regardless of the FRESH/RECIRC push button setting.

When the mode control is at A/C and the FRESH/RECIRC control is set for recirculation (push button in), the system functions the same as when the mode control is at MAX A/C. To prevent the buildup of fumes or odors inside the cab (for ex- ample, from smoking), do not operate the heater and air conditioning system in a recirculation mode for more than 20 minutes. A dash-mounted climate control panel ( Fig. 4.1 ) al- lows you to control all of the heating, air conditioning, defrosting, and ventilating functions. A four-speed fan forces fresh or recirculated air to any selected air outlets at the windshield, door win- dows, dashboard face, and cab floor. See Fig. 4.2 .

All of the dash-face outlets have adjustable louvers that pivot right and left, and up and down. The out- lets can be closed by moving the louvers all the way down. Windshield defrost outlets and the passenger’s door window defrost outlet have nonadjustable lou- vers. The bunk outlet (on the right-hand wall of the bunk) has two sets of vertical louvers that operate like the horizontal dash-face louvers. Defogging and Defrosting Using Fresh Air 1 OFF 2 3 1. Set the mode control (upper lever) to HEAT, the fan switch to OFF and, if so equipped, the bunk fan switch to OFF before starting the engine. See Fig. 4.6 . 4 02/03/95 f830069a Fig.

4.1, Climate Control Panel An auxiliary heater and air conditioner unit is stan- dard when there is a sleeper compartment. The unit is installed in the sleeper baggage compartment and uses the cab’s refrigerant system for air conditioner operation. The unit is equipped with a separate evaporator coil, expansion valve, and fan. It is also equipped with its own heater core and water valve, independent of the cab heater. On vehicles with a 60-inch sleeper the auxiliary unit’s climate control panel ( Fig. 4.3 or Fig. 4.4 ) is located in the shelf area; with a 40-inch sleeper it is mounted on the left front wall.

On vehicles with a 48-inch or 70-inch SleeperCab, the control panel is mounted on the left rear wall or the rear overhead storage compartment. 2. Remove any ice or snow from the outside of the windshield, door windows, and fresh air inlet grille. 3. With the engine at operating temperature, slide the temperature control (lower lever) to WARM. 4. Move the mode control to DEF. In this position the system is engaged to dehumidify the air be- fore heating it, unless the temperature at the evaporator coil is less than 32°F (0°C). Warm, dry air is directed to the windshield. IMPORTANT:

If equipped with a FRESH/ RECIRC push button, the system draws in fresh air when the mode control (upper lever) is at HEAT/DEF or DEF, regardless of the FRESH/ RECIRC push button setting. NOTE: Shutting off the heater supply gate valve (if equipped) on the engine limits the ability to control air conditioning temperature in the cab and in the sleeper. With the valve shut off, warm coolant is no longer available from the engine, and the outlet air temperature controls can’t be used to change air temperature. NOTE: At DEF, airflow is directed to the wind- shield outlets and the extreme left and right dash-face outlets.

To defrost the driver’s door window, turn the extreme left dash-face outlet to direct airflow to the upper left. In all positions of the mode control, airflow is directed to the pas- senger’s door window. 4.1 AX A/C A/C VENT HEAT/DEF DEF