Fuels, Lubricants, and Coolant Biodiesel Fuel Biodiesel is a fuel comprised of monoalkyl esters of long chain fatty acids derived from vegetable oils or animal fats. Biodiesel blends are biodiesel mixed with petroleum diesel fuel on a volume basis. Consult your John Deere dealer for approved biodiesel fuel conditioners to improve storage and performance with biodiesel fuels. Biodiesel users in the U.S. are strongly encouraged to purchase biodiesel blends from a BQ9000 Certified Marketer and sourced from a BQ9000 Accredited Producer (as certified by the National Biodiesel Board). Certified Marketers and Accredited Producers can be found at the following website: http://www.bq9000.org.
When using biodiesel fuel, the engine oil level must be checked daily. If oil becomes diluted with fuel, shorten oil change intervals. Refer to Diesel Engine Oil and Filter Service Intervals for more details regarding biodiesel and engine oil change intervals. The following must be considered when using biodiesel blends up to B20:
Cold weather flow degradation Stability and storage issues (moisture absorption, oxidation, microbial growth) Possible filter restriction and plugging (usually a problem when first switching to biodiesel on used engines.) Possible fuel leakage through seals and hoses Possible reduction of service life of engine components While 5% blends are preferred (B5), biodiesel concentrations up to a 20% blend (B20) in petroleum diesel fuel can be used in all John Deere engines. Biodiesel blends up to B20 can be used ONLY if the biodiesel (100% biodiesel or B100) meets ASTM D6751 (US), EN 14214 (EU), or equivalent specification.
Expect a 2% reduction in power and a 3% reduction in fuel economy when using B20. John Deere approved fuel conditioners containing detergent/dispersant additives are recommended when using lower biodiesel blends, but are required when using blends of B20 or greater. The following must also be considered when using biodiesel blends above B20.
Possible coking and/or blocked injector nozzles, resulting in power loss and engine misfire if John Deere approved fuel conditioners containing detergent/dispersant additives are not used Possible crankcase oil dilution, requiring more frequent oil changes Possible corrosion of fuel injection equipment Possible lacquering and/or seizure of internal components Possible formation of sludge and sediments Possible thermal oxidation of fuel at elevated temperatures Possible elastomer seal and gasket material degradation ( primarily an issue with older engines) Possible compatibility issues with other materials (including copper, lead, zinc, tin, brass, and bronze) used in fuel systems and fuel handling equipment Possible reduction in water separator efficiency Potential high acid levels within fuel system Possible damage to paint if exposed to biodiesel John Deere engines can also operate on biodiesel blends above B20 (up to 100% biodiesel) ONLY if the biodiesel meets the EN 14214 specification (primarily available in Europe).
Engines operating on biodiesel blends above B20 may not fully comply with all applicable emissions regulations. Expect up to a 12% reduction in power and an 18% reduction in fuel economy when using 100% biodiesel. John Deere approved fuel conditioners containing detergent/dispersant additives are required. The petroleum diesel portion of biodiesel blends must meet the requirements of ASTM D975 (US) or EN 590 (EU) commercial standards. Biodiesel blends up to B20 must be used within 90 days of the date of biodiesel manufacture. Biodiesel blends from B21 to B100 must be used within 45 days of the date of biodiesel manufacture.
Request a certificate of analysis from your fuel distributor to ensure that the fuel is compliant with the above specifications. IMPORTANT: Raw pressed vegetable oils are NOT acceptable for use as fuel in any concentration in John Deere engines. Their use could cause engine failure. DX,FUEL7 1904OCT071/1 Testing Diesel Fuel water content, suitability for cold weather operation, and whether the fuel meets specifications. DIESELSCAN™is a John Deere fuel analysis program that can be used to monitor the quality of your fuel. The DIESELSCAN analysis verifies fuel type, cleanliness, Check with your John Deere dealer for availability of DIESELSCAN kits.
DIESELSCAN is a trademark of Deere & Company DX,FUEL6 1914NOV051/1 904 122208 PN=240