Industry Standard Comparison SAE 100R1AT vs Cat One-Wire Braid Hose (716) WORKING PRESSURE* HOSE INNER INNER MAX. WORK. PRESS. MAX. WORK. PRESS. MAX. WORK. PRESS. DASH DIAMETER DIAMETER (psi) (BAR) (kPa) SIZE (in) (mm) 100R1 716 100R1 716 100R1 716 -3 0.188 4.8 3000 207 20,700 -4 0.250 6.4 2750 2750 190 190 19,000 19,000 IMPULSE TESTING NUMBER TEST TEST OF PRESSURE TEMPERATURE CYCLES 100R1 -3 to -16 125% of W.P. N +212°F (+100°C) 150,000 -20 to -32 100% of W.P. +212°F (+100°C) 150,000 716 All Sizes 100% of W.P.
+275°F (+135°C) 250,000# -5 0.313 7.9 2500 172 17,200 -6 0.375 9.5 2250 2250 155 155 15,500 15,500 -8 0.500 12.7 2000 2000 138 138 13,800 13,800 -10 0.625 15.9 1500 1500 103 103 10,300 10,300 -12 0.750 19.1 1250 1250 86 86 8600 8600 -16 1.000 25.4 1000 1000 69 69 6900 6900 TEMPERATURE CAPABILITIES 100R1: -40°F to +212°F (-40°C to +100°C) 716: -40°F to +275°F (-40°C to +135°C) -20 1.250 31.8 625 625 43 43 4300 4300 -24 1.500 38.1 500 500 34 34 3400 3400 -32 2.000 50.8 375 375 26 26 2600 2600 * Minimum burst pressure will always be 4X the maximum working pressure for both Caterpillar and SAE standard hose.
# For this test, 716 hose is aged at +300°F (+150°C) for 200 hours and -25°F (-32°C) for 18 hours prior to impulse testing. In addition, in the middle and at the end of each impulse test, no leaks are allowed after the oil cools to room temperature and the test machine is restarted. SAE does not require aged samples or room temperature leak checks. N W.P. = Working Pressure DIN 20022 1SN vs Cat One-Wire Braid Hose (716) WORKING PRESSURE* IMPULSE TESTING DIN INNER INNER MAX. WORK. PRESS. MAX. WORK. PRESS. MAX. WORK. PRESS.
DN DIAMETER DIAMETER (psi) (BAR) (kPa) SIZE (in) (mm) 20022 1SN 716 20022 1SN 716 20022 1SN 716 NUMBER TEST TEST OF PRESSURE TEMPERATURE CYCLES DIN 20022 1SN 5 to 25 125% of W.P. N +212°F (+100°C) 150,000 32 to 50 100% of W.P. +212°F (+100°C) 150,000 716 5 to 25 125% of W.P. +212°F (+100°C) 150,000# 32 to 50 100% of W.P.
+212°F (+100°C) 150,000# 5 0.188 4.8 3625 250 25,000 6 0.250 6.4 3263 3263 225 225 22,500 22,500 8 0.313 7.9 3118 215 21,500 10 0.375 9.5 2610 2610 180 180 18,000 18,000 12 0.500 12.7 2320 2320 160 160 16,000 16,000 16 0.625 15.9 1885 1885 130 130 13,000 13,000 20 0.750 19.1 1523 1523 105 105 10,500 10,500 25 1.000 25.4 1276 1276 88 88 8800 8800 32 1.250 31.8 914 914 63 63 6300 6300 TEMPERATURE CAPABILITIES DIN 20022 1SN: -40°F to +212°F (-40°C to +100°C) 716: -40°F to +212°F (-40°C to +100°C) 40 1.500 38.1 725 725 50 50 5000 5000 50 2.000 50.8 580 580 40 40 4000 4000 * Minimum burst pressure will always be 4X the maximum working pressure for both Caterpillar and SAE standard hose.
# For this test, 716 hose was tested against the DIN 20022 1SN specifications for use in DIN applications. N W.P. = Working Pressure 6