REAR STEERING (Cont'd.) ------------ .. Ref. Part Ref. Part No. Number Oty. Description No. Number Qly. Description 20. 115--006 2 lerk 11/4-NF X 45 0 ) 43. 182-074 1 l1Flange Yoke [10 spline) 21. 115--483 4 External Klip Ring 44. 183-264 2 Pin [1-114" 00 x 4.37" LG) 22. 115--515 2 Internal Snap Ring 45. 205-671 2 Hub Cap [for 1.98" ID bore)-early style 23. 125--260 4 3Beari ng [2.25" 10) 205-744 2 Hub Cap [for 3.15" 10 bore) 24. 125--261 4 3Race [3.8125" DO) 190-273 10Spindie Bolt Conversion Kit pncl. ref. 125--367 4 4Bearing [2.5" 10) 46. 301-151 4 Spindle Bolt Lock 125--368 4 4Race [4.33" DO) no/s 1,2,4, 13, 25, 27, 38 and 46) 25. 125--301 4 Bushing [1" DO) 47.
312-081 1 Rear Steer Cylinder Mount 26. 125--403 2 Bronze Bushing [.625" 10) 48. 105--031 8 llBolt [3/8-NC xl") 27. 125--716 8 Urethane Flange Bushing [1" 10) 49. 160-799 1 Brake Disc 28. 155-806 4 Internal Seal [1.75" 10 x 2.5" 00) 50. 182-007 2 Cross and Bearing 29. 155-808 4 31nternal Seal [3" 10 x 4" DO) 115--001 lerk [l/B-NPI, SIR) 155-804 4 41nternal Seal [3.25" 10 x 4.5" 00) 115--500 Internal Snap Ring 30. 160-160 2 3Spindle Flange [1.57" 10 w/26 spline)- 180-790 Bearing Cap (greasable) Incl. ref. no. 12 51. 182-013 1 Double Center Yoke lIiIimI 2 4Spindle Flange [1.75" 10 w/43 spline)- 52. 312-228 2 llService Brake Spacer Incl. ref. no. 12 53.
105-516 2 2Roll Pin [3/16" x 1-1/2'1 161-057 2 lSpindle Flange [1.75" ID w/43 spline)- 54. 311-350 3 Bolt Lock Incl. ref. no. 12 55. 105-518 Cotter Pin [1/8" x 1-1/2'1 31. 160-306 2 Tie Rod End [Incl. ref. ne.'s 7 and 55) 56. 105-047 8 12Locknut [3/8-NC) 32. 160-319 1 3Spindle Housing [left on rear diff.) 57. 105-052 8 12Bolt [3/8-NC x 1-1/4'1 33. 160-318 1 3Spindle Housing [right on rear diff.) 3/4-NF with 1-NS spindle shaft you must order new shaft, roll pin, washer and nut. See footnotes 2 and 5. 160-382 1 4Spindle Housing [left on rear diff.) 'Used with spindle shafts which have 3/4-NF threads.
When replacing a 160-381 1 4Spindle Housing [right on rear diff.) 2Used with spindle shaft and yoke which has 1-NS threads. 3Used with spindle shaft and yoke which has either 3/4-NF or 1-NS threads 34. N.A. 2 lSpindle Shaft and Yoke [3/4-NF, 26 spline) and axles with 35 spline on yoke side. 4Used with spindle shaft and yokes which have 1-NS threads and axles with 160-336 2 5Spindle Shaft and Yoke [l-NS, 26 spline) 43 spline on yoke side. See footnote 6. mIiD 2 4Spindle Shaft and Yoke [l-NS, 43 spline) 5Spindle shaft and yoke which has 1-NS threads and is used with axle with 35 spline on yoke side.
160-386 2 7Spindle Shaft and Yoke [1-NS, 43 spline) BThis spindle shaft has 2.69" LG splines that run all the way to the yoke. This flange has a splined .75" 10 that is 2.69" LG. If replacing this style shaft with 35. 160-366 1 Tie Rod shaft which has 1.66" LG splines you must also order new style spindle flange. See footnote 7. 36. 161-006 2 Rear Axle [1.75" 00, 16 & 35 spline) "Ihls spindle shaft has 1.66" LG splines that do not extend to the yoke. This 37. 161-010 1. Rear Differential [Incl. ref. no. 22) 9Converts from Dana to Rockwell differentials. Additional kit parts may be found on REAR STEERING HYDRAULICS and HYDRAULIC CONTROL VALVE. 38.
180-061 4 Spindle Washer Refer to installation diagram 050-127. loRefer to installation diagram 050-946 to install spindle bolt kit. 39. 180-279 2 lWasher [.765" 10) llEarly style differential flange yoke lref. no. 43), having 3/B-NC tapped holes 161-045 2 Rear Axle [1.823" 00, 16 & 43 spline) flange has a splined .75" ID that is 1.74" LG. 8Refer to assembly instructions 052-186. 181-381 2 2Washer [1" 10 x 1-7/8" DOl-early style for mounting brake disc with 1" long bolts Iref. no. 48) and requiring use of service brake spacer (no. 52), is no longer available. See footnote 12. 181-685 2 2Washer [1" 10 x 2.25" DO) '2Present style differential flange yoke (ref. no.
43), having untapped holes for mounting brake disc with 1-1/4" long bolts and locknut (ref. no.'s 56 and 40. 180-724 2 3Cross and Bearing [Incl. ref. no. 18) 57), requires no service brake spacer. See footnote 3. 41. 181-397 1 Pinion Yoke Washer 182-099 2 4Cross and Bearing pncl. ref. no. 18) 42. 182-103 2 3Axle Yoke [35 spline) 182-100 2 4Axle Yoke [43 spline) 36025-36030 36